Ding Xinda activated carbon pigment related questions

Answers
Asked by
Updated
Ding Xinda activated carbon pigment02022-01-17 23:33:33
1. Activated carbon treatment of wastewater containing chromium. Chromium is a kind of metal raw material used in electroplating. The hexavalent chromium in wastewater exists in different forms with different pH values. Activated carbon has a very developed microporous structure and high specific surface area, has a strong physical adsorption capacity, can effectively adsorb Cr (V) in wastewater. There are a large number of oxygen-containing groups on the surface of activated carbon, such as hydroxyl (-OH), carboxyl (-COOH), etc., which all have the function of electrostatic adsorption and produce chemical adsorption on Cr (VI). It can be completely used to treat Cr (VI) in electroplating wastewater, and the adsorbed wastewater can meet the national discharge standard. The results showed that when the mass concentration of Cr (VI) in the solution was 50mg/L, pH=3 and adsorption time was 1.5h, the adsorption performance and Cr (VI) removal rate of activated carbon reached the best effect. Therefore, the process of treating wastewater containing chromium by activated carbon is the result of the comprehensive action of physical adsorption, chemical adsorption and chemical reduction of Cr (VI) in solution by activated carbon. Activated carbon treatment of wastewater containing chromium has stable adsorption performance, high treatment efficiency, low operating cost, and certain social and economic benefits. 2. Treatment of cyanide-containing wastewater with sexual carbon. In industrial production, cyanide or by-product cyanide is used in the wet extraction of gold and silver, the production of chemical fiber, coking, synthesis of ammonia, electroplating, gas I production and other industries, so a certain amount of cyanide-containing wastewater must be discharged in the production process. Activated carbon has been used to purify wastewater for a long time and there are more and more reports on its application in the treatment of cyanide-containing wastewater. However, due to the small adsorption capacity of CN_ and HCN on activated carbon, which is generally 3mgCN/ GAC --8mgCN/ GAC depending on the variety, it is not cost-effective in the treatment cost. 3. Activated carbon treatment of wastewater containing mercury. Activated carbon has the ability to adsorb mercury and mercury-containing compounds, but its adsorption capacity is limited, and it is only suitable for treating wastewater with low mercury content. If the concentration of mercury is high, it can be treated by chemical precipitation method first. After treatment, the mercury content is about 1mg/L, and it can reach 2-3mg /L when high, and then further treatment with activated carbon. 4. Activated carbon treatment of phenol-containing wastewater. Phenol-containing wastewater is widely sourced from petrochemical plants, resin plants, coking plants and oil refining and chemical plants. The experimental results show that the activated carbon has a good adsorption performance for phenol, but the increase of temperature is not conducive to adsorption, so that the adsorption capacity is reduced. But the time to reach adsorption equilibrium is shortened by increasing the temperature. The optimum values of the amount of activated carbon and the adsorption time were found, and the removal rate changed little under acidic and neutral conditions. Under the condition of strong alkalinity, the removal rate of phenol decreased sharply, the stronger the alkalinity, the worse the adsorption effect. 
Ding Xinda activated carbon pigment and price02022-01-17 23:34:21
Microwave heating can produce good effects in the preparation and modification of activated carbon (S2. Microwave modification, many backwater hole is opened, the distributed capacitance change obviously, promoting the improvement of the adsorption. The microwave power and irradiation time are key determinants of modified activated carbon adsorption performance. On the mechanism of microwave carbonization and activation, it is generally believed thatgold adsorption on activated carbon  Microwave refers to the electromagnetic radiation located between far-infrared and radio waves in the electromagnetic spectrum, with a frequency range of 300MHz to 300GHz and a wavelength of 1m to 1mmMicrowave generates "internal friction heat" through high frequency reciprocating motion of dipole molecules in the heated body, which raises the temperature of the material. It does not require any heat conduction process, and has the characteristics of high efficiency, selectivity, non-contact, integrity, uniformity, quick start and stop, and easy operation Studies have shown that activated carbon can effectively absorb microwave energy and make the temperature rise to 110o℃5' within a few minutes.www.chinactivecarbon.com  Microwave heating can produce good effects in the preparation and modification of activated carbon (S2. Microwave modification, many backwater hole is opened, the distributed capacitance change obviously, promoting the improvement of the adsorption. The microwave power and irradiation time are key determinants of modified activated carbon adsorption performance. On the mechanism of microwave carbonization and activation, it is generally believed that Plant waste is mostly made of plant fiber raw materials, in the plant body under the action of capillary, modified solution absorbed by material whole fully, between fiber is filled with the subtle space, make the dry material volume expansion after soaking wet, and reaction. Because of the water in the raw material, modified solution constitute a polar molecule, with a strong absorption of microwave dielectric properties,Therefore, polar molecules collide and rub violently with microwave frequency, generating a large amount of heat, which makes water and modified solution volatilize rapidly, and generate steam pressure, which explodes out from the inside of the raw material to the outside. This sharp action makes the fiber space of the raw material expand and produce sharp drying.In this way, the raw material has a more obvious pore structure and a larger internal specific surface area than before microwave irradiation. Compared with the traditional heating method, the mechanism of microwave in the preparation process of activated carbon is completely different.It shows its unique advantages: high efficiency, energy saving, uniformity, selectivity, low pollution, high thermal efficiency, low energy consumption, simple process and equipment and small footprint, conducive to automation, low carbon loss, and recovery of useful substances. Many theoretical problems in this new field, especially the microwave heating mechanism, need to be further studied, and the mathematical model of the heating process needs to be established 
Ding Xinda activated carbon carbon adsorption and carbon principle02021-11-29 22:41:57
② chemical activation method.Activated carbon can be obtained after high temperature treatment by using the gas released by the activator or soaking the raw material with the activator.Activated carbon has a micro product structure, the micro product arrangement is completely irregular, the product body has micropores (radius is less than 20[angstroms]=10-10 meters), through the hole (halfDiameter 20~1000), large hole (radius 1000~100000), so that it has a large inner surface, specific surface area of 500~1700 m 2/ g.This determines that activated carbon has good adsorption, can adsorb the metal ions in waste water and waste gas, harmful gases, organic pollutants, pigments and so on. gold coconut shell activated carbon  Industry should beActivated carbon also requires high mechanical strength, good wear resistance, its structure is stable, small energy required for adsorption, in order to be conducive to regeneration.Activated carbon for oilDecolorization, deodorization, gas separation, solvent recovery and air conditioning of fat, beverage, food and drinking water, used as catalyst or adsorbent for body and gas mask.Physical characteristics:Activated carbon is a kind of multi-aperture carbonization, has a very rich pore structure, has good adsorption characteristics, its adsorption by physical and chemicalAbsorbed from the force, the appearance of the color and lustre is black.Its composition in addition to the main carbon, but also contains a small amount of hydrogen, nitrogen, oxygen, its structure is shaped like a hexagon, due to the irregular hexagon structure, determine the characteristics of its body also incandescentand high surface area, each gram of activated carbon has the equivalent of 1000 square meters than the surface. 
Ding Xinda activated carbon use02021-12-22 00:10:48
High-quality granular activated carbon must have good adsorption performance and strength. Like powdery activated carbon, the adsorption performance of granular activated carbon depends largely on the characteristics of pore structure. The adsorption performance index can be analyzed and characterized by different methods, such as the decolorization performance of activated carbon expressed by methylene blue. Other performance indexes include iodine adsorption value, caramel decolorization rate, etc.activated carbon for gold recovery  The pore structure characteristics and specific surface area of activated carbon are usually obtained by measuring nitrogen adsorption isotherm at low temperature with adsorption apparatus.activated carbon wholesale  For the gas phase adsorption, the size of the gas molecules is usually less than 1. ONM, the use of microporous activated carbon; For liquid-phase decolorization refining, due to the large size of the liquid molecules, it is necessary to use activated carbon with developed mesopore. Activated carbon has a large specific surface area and a particularly developed micro-pore structure, which is the main reason for its strong adsorption capacity and large adsorption capacity. 
Ding Xinda activated carbon use02021-12-13 00:44:20
2.1.3 Determination of ash content. Put 150mL porcelain cyanosis pot in muffle furnace, burn it at (65020) "℃ to constant weight, put the cyanosis pot in dryer, cool and weigh; Weigh 5 grams of the crushed sample (approximately 0.1mg) and place it in 150mL porcelain coating that has been burned to constant weight; Put Zengtan into a muffle furnace whose temperature does not exceed 300℃, open the cyanosis cap, and gradually increase the temperature to a constant weight at 650 ℃ 20℃. It takes about three hours. Calculate ash value and get ash content.activated carbon for gold recovery  2.1.4 Determination of methylene blue adsorption value. The crushed sample was weighed with 1.0 grams (approximately to 1mg) and placed in a 100mL grinding stopper conical flask. An appropriate amount of methylene blue test solution was added with an eyedrot. The filtrate was placed in a colorimetric dish with a light diameter of LCM, and the absorbance was measured with a spectrophotometer at a wavelength of 665nm. The absorbance was compared with the absorbance of the standard cupric sulfate filter. The number of ml of methylene blue test solution consumed was the methylene blue adsorption value of the sample. activated carbon wholesale  
Ding Xinda activated carbon value02021-12-29 21:32:21
At present, the organic pollution of drinking water source is relatively serious. The organic pollutants themselves are not only highly toxic, but also may generate halogenated disinfection by-products (DBPs) after chlorination disinfection. Meanwhile, the existence of organic compounds will reduce the biological stability of drinking water and lead to the secondary reproduction of microorganisms in the pipe network. Therefore, it is important to reduce the content of organic pollutants in drinking water. Conventional water treatment process has low removal efficiency for organic pollutants, so it is imperative to seek economic and efficient treatment technology. On the basis of giving full play to the advantages of ozone oxidation to remove organic matter, ozone catalytic oxidation technology can induce the formation of highly oxidizing hydroxyl radical (-Oh), which can effectively remove trace organic pollutants that are difficult to degrade in water and reduce the content of ozone oxidation by-products. It is a kind of water treatment method with great prospect.activated carbon for gold recovery  Laboratory studies have shown that ceramic honeycomb activated carbon catalytic ozone oxidation technology and removal of trace organic matter in water has more obvious advantages, but the catalytic oxidation and active carbon process characteristics to be in-depth study, therefore the pilot was investigated through honeycomb ceramic catalytic ozonation and activated carbon catalytic ozonation and activated carbon filter combination process operation characteristics. activated carbon wholesale 
Ding Xinda activated carbon decomposition02021-12-14 23:34:22
The experimental results show that the adsorption equilibrium of pure components is in good agreement with the Langmuir equation. In the case of multi-component adsorption, due to the competition and interference between each component, the component with strong adsorption ability can replace the other component that has been absorbed, so that the penetration curve of each component has obvious changes. activated carbon for gold recovery  The penetration point of the components with relatively weak adsorption capacity was significantly advanced, while the penetration time of the components with strong adsorption capacity was delayed. In this paper, E-L equation and IAST theory are used for theoretical prediction and analysis of multi-component adsorption equilibrium, and compared with experimental results.activated carbon wholesale   The results show that although the prediction of total adsorption amount by E-L equation is in good agreement with the experimental results, the prediction of each component adsorption amount by E-L equation often produces positive and negative deviation, and the average error is usually more than 20%. However, IAST can eliminate the positive and negative deviation well, and the average error is less than 10%, which is more consistent with the experimental results. The operating parameters showed that the adsorption capacity of activated carbon would decrease with the increase of temperature, gas velocity or humidity. The appropriate operating range is: temperature within 40℃, gas speed between 0.1~0.5 m/s, humidity is best not more than 40%. In this rang 
Ding Xinda activated carbon price02021-12-13 23:00:10
The isobarisothermal adsorption properties of activated carbon at different temperatures, at different pressures and at different flow rates were determined by using the gas produced in the system as samples.The adsorption effluent curve of benzene by activated carbon was plotted.activated carbon wholesale   The effects of different temperature on the regeneration performance of activated carbon under static environment, the effects of steam at different temperature on the regeneration performance of activated carbon under dynamic environment and the effects of nitrogen at different temperature on the regeneration performance of activated carbon under dynamic environment were studied.activated carbon for gold recovery  The experimental results showed that high pressure and low temperature were beneficial to the adsorption, and the flow rate had little effect on the equilibrium adsorption capacity in the range of experimental flow rate. The adsorption capacity of benzene by activated carbon in the experiment was 150~170mg/g under operating conditions. At the same time, the filtration and adsorption properties of coke were tested. The experiment shows that the adsorption performance of the test coke on benzene is very weak, can not be used as the nitrogen adsorbent, but the coke filter and adsorption performance of ash and naphthalene is very good, the content of naphthalene and ash after the gas through the coke column completely meet the design requirements. 
Ding Xinda activated carbon solvent02021-12-17 23:14:06
 www.powdered-activated-carbon.com cIn painting, printing, shoe making, plastic, rubber, bonding and other industrial processes, there are a large number of organic waste gas emissions.These waste gas, often contain benzene, toluene, xylene, ethyl acetate, methanol and other organic matter, itself toxic, long-term damage can lead to human death.The emission of this kind of waste gas, countries have clear provisions, strict control of its emission concentrationThe treatment of organic waste gas has been studied for a long time, and some effective control technologies have been developed.The widely used and studied control techniques include adsorption method, thermal destruction method, condensation method, absorption method, etc.activated carbon pellets wholesale  emissions.It is estimated that more than 30 million tons of organic matter are released into the atmosphere worldwide every year, posing a serious threat to human health and plant and animal growth.Organic pollutants are mostly produced in industrial processes. In painting, printing, shoe making, plastic, rubber, bonding and other industrial processes, there are a large number of organic waste gas emissions.These waste gas, often contain benzene, toluene, xylene, ethyl acetate, methanol and other organic matter, itself toxic, long-term damage can lead to human death.The emission of this kind of waste gas, countries have clear provisions, strict control of its emission concentrationThe treatment of organic waste gas has been studied for a long time, and some effective control technologies have been developed.The widely used and studied control techniques include adsorption method, thermal destruction method, condensation method, absorption method, etc. 
Ding Xinda activated carbon treatment02022-01-19 22:21:13
CO, the activator, the activation of the burning loss rate is large. However, the pore structure of activated carbon was not developed, indicating that the newly formed potassium carbonate in the pore channels was more likely to react with carbon during the activation process of potassium hydroxide, and the pore structure was further developed.gold adsorption on activated carbon  According to the standard Gibbs free energy of the reaction, K· Co; (or K;O) direct reaction with carbon is difficult to be carried out at the activation temperature of 730℃, indicating that they react with -CH- and -CHZ - in petroleum coke and play an activation role.The elemental potassium generated from the activation reaction intercalated and activated the petroleum coke, and the specific surface area of the activated product reached 98m'g1.XRD analysis showed that there were potassium to graphite intercalated compounds in the activated product.According to the study results of activation mechanism, the mixing of additive N can improve the dispersion of alkali and the activation of additive N at high temperature to improve the activation effect.Activated carbon with a yield of 68% and a specific surface area of 2532m'g can be obtained under the conditions of alkali-coke ratio of 3:1, activation temperature of 730℃ and activation time of 30 minutes.At the same time, the amount of hydrogen produced in the activation reaction is large, reaching 38cm'g 'min', and hydrogen can be separated and purified.www.chinactivecarbon.com   Thus, a one-step process for the preparation of activated carbon with high specific surface area was proposed.Compared with the conventional method, the process reduces the production cost, shortens the production time, saves energy, and lays a foundation for further industrial production.The prepared petroleum coke based activated carbon was used as the carrier.The catalyst supported by Ni-Mo has similar hydrodesulfurization activity with commercial catalysts. The DBT conversion rate is more than 98% at 290℃ and the catalyst has high stability.The pore size distribution of petroleum coke based activated carbon with high specific surface area is mostly between 1.0~ 2.0nm. The methane storage experiment using this sample shows that it has a high methane storage performance: at 1.4 MPa, room temperature, the mass adsorption capacity of methane is 0.112 Gg 
Ding Xinda activated carbon raw material use02022-01-13 23:16:06
The maintenance sewage contains a large number of complex biodegradable substances, biodegradability is poor, for many years mainly rely on fresh water dilution treatment and combustion furnace treatment, but these two methods are low efficiency and high cost, so it is necessary to develop new wastewater treatment methods.www.chinactivecarbon.com   Although we have studied the upflow anaerobic sludge bed reactor (UASB) for the treatment of high concentration sewage of the natural gas purification plant, the start-up test results of 133 days show that the effluent COD removal rate is only about 40% when the influent COD is 6000mg/L, and the treatment effect is not good. Therefore, it is of practical significance to explore and seek an effective pretreatment method.gold adsorption on activated carbon  In this paper, Fenton oxidation and activated carbon adsorption were combined to pretreat the wastewater from natural gas purification maintenance, in order to improve the subsequent operation efficiency of UASB. This experiment by orthogonal test to determine the Fenton reagent oxidation first preliminary operating conditions, on this basis, carries on the single factor analysis method, the main factors influencing the Fenton reagent treatment effect for each study, investigation of its influence on wastewater COD removal rate, the results show that Fenton oxidation method the optimum operating conditions for natural gas purification overhaul wastewater treatment: HO2 dosing quantity 0.3 mol/L, n (HO)/n (Fe) = systematically, initial pH = 3, reaction temperature 70 ℃, reaction time, 40 min. Under these conditions, the COD removal rate reached 78.6%, the BOD /COD value increased from 0.168 to 0.353-0.403, and the biodegradability was greatly improved. If Ho is added in three times and the interval time is 10min, the COD removal rate will increase from 78.6% to 80.3%. Therefore, it can be seen that H0: batch addition will further improve the reaction effect. After Fenton oxidation treatment, wastewater and activated carbon adsorption, this topic activated carbon adsorption experiments using single factor method, examines different PH, activated carbon adsorption dosing quantity and the influence of adsorption time of wastewater COD removal rate, the results show that after Fenton oxidation treatment without having to adjust PH value, according to the 20 g/L after adding the activated carbon reaction 3 h at room temperature, COD removal rate was 47.3%,, BOD/COD value of 0.438 to 0.625. The research in this paper has laid a theoretical foundation and provided an experimental basis for the practical application of Fenton oxidation and activated carbon adsorption in the pretreatment of natural gas purification maintenance wastewater in UASB reactor. 
Ding Xinda activated carbon insoluble02021-10-26 22:56:50
The effect of the amount and adding method of activated carbon on smoke emission of cigarettes was investigated. It was found that the filtration efficiency of ternary compound filter was higher than that of binary compound filter under the influence of plasticizer when the amount of activated carbon was constant. With the increase of the amount of activated carbon, the filtration efficiency of the two kinds of composite filters increases. The effects of the amount of activated carbon on the filtration efficiency of the compounds with different volatiles are different. The effects of the amount of activated carbon on the filtration efficiency of the isomers are similar due to their close molecular weight and boiling point. When the dosage is small, the competitive adsorption is easy to occur. The adsorption amount of refractory components such as acetaldehyde is small, and the competition can be reduced by increasing the dosage. The filtration efficiency of refractory components shows an obvious upward trend with the increase of the dosage. It was found that the contents of volatile compounds and flavor components were related to the type of cigarettes and the amount of tar. The contents of volatile compounds and flavor components were higher in the flue-cured cigarettes than in the mixed cigarettes, and higher in the high tar cigarettes than in the low tar cigarettes. The types of fragrance components in smoke of different types of cigarettes are basically the same, but there are great differences in content. The contents of furfural, furfuryl alcohol, maltol, 5-hydroxymethylfurfural, linolenic acid, methyl linolenic acid, linoleic acid, methyl palmitate and other components in flue-cured cigarettes were significantly higher than those in mixed cigarettes. This is related to the higher carbohydrate content in flue-cured cigarettes. Mixed-type cigarettes contain high content of 3-methylpentanoic acid and nitrogen heterocyclic compounds such as cotinine, ho ah, and methamine due to their formulations of burley tobacco and spice tobacco. The filtering law of activated carbon for different types of cigarettes is basically the same, that is, the filtering efficiency is related to the properties of compounds, especially with the molecular weight and boiling point of compounds. The filtration efficiency of activated carbon on flue-cured cigarettes was lower than that of mixed cigarettes. 

Ask New Question  

  • You are not logged in,answer will be Anonymous.Set Nickname | Sign In | Sign Up
  • tags separate by ','
  • Shortcuts:Ctrl+Enter

Latest Questions