Study on Preparation of Modified Activated Carbon and Its Adsorption Performance of Heavy Metals related questions

Answers
Asked by
Updated
Study on Preparation of Modified Activated Carbon and Its Adsorption Performance of Heavy Metals02022-01-12 23:18:50
Factors such as [10. For honeycomb activated carbon, the wall thickness is a very important parameter, by changing the wall thickness to improve its adsorption efficiency. Under the same porosity, thickness increases, the honeycomb carbon content per unit volume also will increase, which can improve the adsorption capacity. This is because the wall thickness increases, the fluid channel in the cellular cross-sectional area reduced, so the real surface or volume flow rate will increase. At the same time, the contact between adsorbate and carbon efficiency will, there is a balance between the two. Under the given conditions, the balance will determine adsorption increase or decrease. If the adsorbate at higherthe diffusion rate diffuses to the inside of the honeycomb wall, and the empty adsorption site can be continuously adsorbed, so the thick-walled honeycomb should have better adsorption efficiency and adsorption capacity"Determination of air velocity and cross-sectional area of empty towerThe empty tower gas velocity is the velocity of gas passing through the entire cross section of the adsorber.The selection of air velocity not only directly determines the size and pressure drop of the adsorber, but also affects the adsorption efficiency. www.powdered-activated-carbon.com  If the gas speed is very small, the size of the adsorber is large and uneconomical. If the gas velocity is too large, the pressure drop will increase and the adsorption efficiency will be affected.The optimum gas velocity was determined by experiment. imagitarium activated carbon pellets  
Study and application of additives in the preparation of activated carbon02021-07-11 19:47:28
The purification efficiency of liquid absorption method is 60%~ 80%, which is suitable for treating low concentration and large volume of organic waste gas, but there are secondary pollution.coal based activated carbon price  The purification rate of catalytic combustion method is 95%, which is suitable for the treatment of high concentration and small air volume organic waste gas. The disadvantage is that it has strict requirements on the treatment object and requires high gas temperature. In order to improve the exhaust gas temperature, it needs to consume a lot of fuel, so the operation cost is very high.https://www.granular-activated-carbon.com/  The purification efficiency of activated carbon adsorption method is 99.2%~99.3%. For the treatment of large air volume and low concentration of organic waste gas, it is agreed that this method is the most mature and reliable technology at home and abroad, but the T art process is too long, the operation cost is high, and it is often more difficult to need a stable steam source. In view of these problems, combined with the characteristics of this graduation design and only body requirements, the use of activated carbon fixed bed adsorption system for industrial organic waste gas purification, the selection of honeycomb activated carbon as adsorbent.The process system is compact and integrated with adsorption and desorption. The waste gas produced in the production process, mainly of benzene, toluene, xylene, etc., according to the nature of benzene class, this scheme adopts the active carbon as adsorbent to absorb the waste gas, the adsorption bed configuration 2 sets of above commonly, use rotation, when one adsorption bed adsorption of organic adsorption amount of reach regulation, change to another Ⅰ adsorption bed for adsorption purification operation, at the same time to take off one in front of the adsorption bed with regeneration.Desorption is carried out by heating under the action of additional steam, and most of the hotgas released by the tail gas is used for desorption and regeneration of adsorbent in the adsorption bed to achieve the utilization of waste heat.The waste gas volatilized from production is sent to the adsorption tower by centrifugal fan with activated carbon as adsorbent. The gas in the tower is processed through the activated carbon filter layer from right to left and from bottom to top, and the purified gas is discharged into the atmosphere through the exhaust pipe. 
Study and application of additives in the preparation of activated carbon02021-08-26 23:23:03
Increase the number of activated carbon mesh and millimeter corresponding table content and related websites. It's not advertising. It's a lot of help to consumers. Now activated carbon is in accordance with the eye, but we do not know that the eye can be changed into millimeters. pelletized activated carbon  Activated carbon is widely used in all aspects of industrial and agricultural production, such as the petrochemical industry without alkali deodorization (refined demercaptan), ethylene desalting water (refined filler), catalyst carrier (palladium, sales, men, etc.), water purification and sewage treatment; Water quality treatment and protection of power plants in the power industry; Chemical industry of chemical catalyst and carrier, gas purification, solvent recovery and oil and other decolorization, refining; Food industry beverage, wine, MSG mother liquor and food refining, decolorization; Gold extraction and tailings recovery in the gold industry; Environmental protection industry sewage treatment, waste gas and harmful gas treatment, gas purification; As well as related industries of cigarette filter, wood floor moistureproof, taste absorption, automobile gasoline evaporation pollution control, the preparation of various impregnation liquid, etc. Activated carbon in the future will have excellent development prospects and broad sales market.  www.powdered-activated-carbon.com  
Study and application of additives in the preparation of activated carbon0CLMnb2021-09-03 20:26:53
Electrochemical modification is to change the electrical and chemical properties of activated carbon surface by using micro electric field, so as to improve the adsorption selectivity and performance.It does not need to add chemical agents, does not need to heat, does not cause pollution to the environment, low energy consumption, only a few hundred millivolts, easy to operate.The results show that the adsorption equilibrium of activated carbon is dependent on the electric potential: the adsorption amount of activated carbon increases with the increase of the potential, and the adsorption speed is accelerated;Arpolarity polarization is beneficial to the adsorption of chloroform by activated carbon, while cathodic polarization inhibits the adsorption of chloroform by activated carbon 3-341]. Activated carbon heteroatom carrier and compound modificationActivated carbon has very high stability and good activity, these two basic properties become the activated carbon as a catalyst or catalyst carrier conditions.By introducing certain heteroatoms and compounds on the surface of activated carbon by liquid phase deposition, the adsorption performance of activated carbon can be increased by using the binding effect between these substances and adsorbents.compounds, which has the advantages of increasing the reaction rate and increasing the adsorption capacity.Yang Quanhong et al. 'Using FESO;Activated carbon material was modified.https://www.granular-activated-carbon.com  The experimental results show that the surface structure of the activated carbon material modified by FeSO changes: the specific surface area decreases, the surface oxygen content increases, the plane of the random layer graphite carbon net is destroyed to a certain extent, and the ammonia absorption capacity and benzene absorption performance of the sample are greatly enhanced.He ChunHong et al. [reported the research progress of supporting activated carbon materials in the removal of SO; the removal ability of SO was significantly enhanced after supporting Co, Ni, Mg, and V compounds, which was due to the formation of Co(OH)2, Ni(OH)2, Mg (OH)2, and V,0 microcrystals on the surface of activated carbon after supporting, which enhanced the desulfurization activity of activated carbon. coal based granular activated carbon  
Study and application of additives in the preparation of activated carbon02021-09-02 00:29:22
Increase the number of activated carbon mesh and millimeter corresponding table content and related websites. It's not advertising. It's a lot of help to consumers. Now activated carbon is in accordance with the eye, but we do not know that the eye can be changed into millimeters.pelletized activated carbon  Activated carbon is widely used in all aspects of industrial and agricultural production, such as the petrochemical industry without alkali deodorization (refined demercaptan), ethylene desalting water (refined filler), catalyst carrier (palladium, sales, men, etc.), water purification and sewage treatment; Water quality treatment and protection of power plants in the power industry; Chemical industry of chemical catalyst and carrier, gas purification, solvent recovery and oil and other decolorization, refining; Food industry beverage, wine, MSG mother liquor and food refining, decolorization; Gold extraction and tailings recovery in the gold industry; Environmental protection industry sewage treatment, waste gas and harmful gas treatment, gas purification; As well as related industries of cigarette filter, wood floor moistureproof, taste absorption, automobile gasoline evaporation pollution control, the preparation of various impregnation liquid, etc. Activated carbon in the future will have excellent development prospects and broad sales market. Adsorption capacity refers to the amount of adsorbents adsorbed on the adsorbent per unit mass under certain conditions. It is usually expressed in terms of K adsorbents /kg of adsorbent or mass percentage, which is a sign of the adsorption capacity of the adsorbent.www.powdered-activated-carbon.com  In industry, the amount of adsorption is called the activity of the adsorbent. The activity of the adsorbent can be expressed in two ways :(1) the static activity of the adsorbentUnder certain conditions, the equilibrium adsorption capacity of the adsorbent is its static activity.For a certain adsorption system, the static activity depends only on the adsorption temperature and the concentration or partial pressure of the adsorbed substance. Dynamic activity of adsorbents 
Study and application of additives in the preparation of activated carbon02022-02-10 18:44:09
The purification efficiency of activated carbon adsorption method is 99.2%~99.3%. For the treatment of large air volume and low concentration of organic waste gas, it is agreed that this method is the most mature and reliable technology at home and abroad, but the T art process is too long, the operation cost is high, and it is often more difficult to need a stable steam source. activated charcoal suppliers & manufacturers  In view of these problems, combined with the characteristics of this graduation design and only body requirements, the use of activated carbon fixed bed adsorption system for industrial organic waste gas purification, the selection of honeycomb activated carbon as adsorbent.The process system is compact and integrated with adsorption and desorption.www.wyactivatedcarbon.com   The waste gas produced in the production process, mainly of benzene, toluene, xylene, etc., according to the nature of benzene class, this scheme adopts the active carbon as adsorbent to absorb the waste gas, the adsorption bed configuration 2 sets of above commonly, use rotation, when one adsorption bed adsorption of organic adsorption amount of reach regulation, change to another Ⅰ adsorption bed for adsorption purification operation, at the same time to take off one in front of the adsorption bed with regeneration.Desorption is carried out by heating under the action of additional steam, and most of the hotgas released by the tail gas is used for desorption and regeneration of adsorbent in the adsorption bed to achieve the utilization of waste heat.The waste gas volatilized from production is sent to the adsorption tower by centrifugal fan with activated carbon as adsorbent. The gas in the tower is processed through the activated carbon filter layer from right to left and from bottom to top, and the purified gas is discharged into the atmosphere through the exhaust pipe. 
Study and application of additives in the preparation of activated carbon02021-09-06 23:16:23
Particle strength is also a main index of granular activated carbon. In order to improve the particle strength of granular activated carbon, usually take some special processing measures, such as adding some material help plasticizing and proper mechanical treatment 4 or control in the process of kneading kneading temperature and kneading time, can greatly improve the strength of granular activated carbon particles, making the strength of the granular activated carbon has reached the fruit shell carbon intensity index.activated charcoal pellets  apparatus. For the gas phase adsorption, the size of the gas molecules is usually less than 1. ONM, the use of microporous activated carbon; For liquid-phase decolorization refining, due to the large size of the liquid molecules, it is necessary to use activated carbon with developed mesopore. https://www.granular-activated-carbon.com  Activated carbon has a large specific surface area and a particularly developed micro-pore structure, which is the main reason for its strong adsorption capacity and large adsorption capacity. 
Study and application of additives in the preparation of activated carbon02021-08-31 20:08:33
Study and application of additives in the preparation of activated carbon The porous structure of activated carbon determines that activated carbon has many excellent properties. Different pore size distribution can play its corresponding function. Therefore activated carbon is widely used in air purification, water treatment and environmental aspects, such as catalyst and 6 carriers [[68, water treatment, etc. The activated carbon adsorption performance to a large extent depends on the pore structure characteristics, the processing of different objects, different requirements for the distribution of pore structure [7071]. This objectively requires the distribution of the activated carbon pore structure should be diversified. At the same time, pore structure and surface chemical properties of activated carbon can be improved by using the method of chemical physics modification!, this is to pass on the modified activated carbon to its better performance. In the process of carbonization and activation,  As one of the means of harmless waste treatment, incineration method can quickly realize the reduction of waste, harmless and recycling, so it has been more and more widely used in China. In the process of waste incineration, toxic organic compounds such as dioxins are inevitably produced, which causes environmental pollution problems.pelletized activated carbon  Activated carbon powder injection combined with bag dust collector (ACI+ BF) is an effective and widely used method to control dioxin emission from incinerator flue gas.www.powdered-activated-carbon.com  In order to provide reference and theoretical basis for the preparation and selection of activated carbon for the adsorption of dioxins, this paper carried out a study on the combined technology of activated carbon injection and double bag dust collector, the characteristics of activated carbon adsorption for dioxins and the influencing factors of activated carbon adsorption for dioxins.The adsorption and desorption isotherms of 13 kinds of commercial activated carbon were determined by low temperature nitrogen adsorption method, and the physical structures of activated carbon were calculated according to BET, T-Plot, BJH and DFT theory, and the iodine value and methylene blue value of 4 kinds of activated carbon were detected. The physical structure characteristics of activated carbon were analyzed in detail to prepare for the subsequent experiment. The preparation methods of activated carbon include physical method, chemical method, microwave radiation method, etc.(1) Physical method. Physical method is to use carbon dioxide, water vapor or the mixture of both as activator, the carbonized carbon material and gas in the activation furnace at 500~1200℃ for carbon activation reaction, so that the pore size of the carbonized material to expand, the formation of activated carbon with porous microcrystalline structure.Gas activation method mainly includes carbonization and activation engineering.The so-called carbonization, refers to the low temperature (about 500℃) is small, the volatile coal tar molecules in the material and the thermal decomposition and curing process of asphalt, that is, to remove the volatile in advance, made suitable for the next step of activation with carbonization. When the temperature is below 600℃, the specific surface area of carbonized material increases with the increase of temperature.When 600~900℃, the specific surface area reaches a certain value: 250~300 m2/g; when above1000℃, the specific surface area shrinks rapidly. When the carbonization temperature is above 800℃, the reaction performance of carbonized compounds and activation gas gradually becomes weaker, so the carbonization temperature is generally below 1000℃. However, if the residual volatile content and thermal effect are taken into account, the most suitable temperature should be 600~700℃39]. The carbonized substance obtained from the carbonization process is placed in water vapor or a mixture of water vapor and combustion gas and heat treated at 800~1000℃, which is called the activation process. 
Activated carbon adsorption performance parameters02022-01-12 23:19:42
Factors such as [10. For honeycomb activated carbon, the wall thickness is a very important parameter, by changing the wall thickness to improve its adsorption efficiency. Under the same porosity, thickness increases, the honeycomb carbon content per unit volume also will increase, which can improve the adsorption capacity. This is because the wall thickness increases, the fluid channel in the cellular cross-sectional area reduced, so the real surface or volume flow rate will increase. At the same time, the contact between adsorbate and carbon efficiency will, there is a balance between the two. Under the given conditions, the balance will determine adsorption increase or decrease. If the adsorbate at higherthe diffusion rate diffuses to the inside of the honeycomb wall, and the empty adsorption site can be continuously adsorbed, so the thick-walled honeycomb should have better adsorption efficiency and adsorption capacity"Determination of air velocity and cross-sectional area of empty towerThe empty tower gas velocity is the velocity of gas passing through the entire cross section of the adsorber.The selection of air velocity not only directly determines the size and pressure drop of the adsorber, but also affects the adsorption efficiency.gold adsorption on activated carbon  If the gas speed is very small, the size of the adsorber is large and uneconomical.www.chinactivecarbon.com   If the gas velocity is too large, the pressure drop will increase and the adsorption efficiency will be affected.The optimum gas velocity was determined by experiment. The adsorption design can not pursue too high adsorption efficiency, the empty tower speed value is reduced, it will make the adsorption bed volume, the amount of adsorbent and equipment cost increased greatly;On the contrary, it is not appropriate to take too large empty tower gas speed. Although the equipment cost is low, the adsorption efficiency drops a lot, and the pressure drop of the system will rise rapidly with the increase of the empty tower speed, resulting in excessive power consumption. Therefore, due to the selection of the appropriate air speed of the empty tower, the most suitable air speed of the empty tower is 0.8~1.2m/s"21, according to the empirical conclusion, this design determines Air velocity of empty tower :U= 1.0m /s.Original conditions:Treatment air volume :Q=20000 m'h, design temperature is 35° C, pressure is 1.01325×103Pa Since the proportion of air in exhaust gas is far greater than that of pollutants, the properties of exhaust gas can be approximately viewed as the thermophysical properties of dry air. Please refer to Appendix 9 of Principles of Chemistry to obtain the following data:Properties of air mixture:Fluid density P;=1.147kg/ m', viscosity u,= 1.94×10-5 Pa.S, specific heat capacity C,=1.005kJ/(kg."C) 
Activated carbon adsorption performance parameters02021-06-11 00:59:21
The experimental results show that the adsorption equilibrium of pure components is in good agreement with the Langmuir equation. In the case of multi-component adsorption, due to the competition and interference between each component, the component with strong adsorption ability can replace the other component that has been absorbed, so that the penetration curve of each component has obvious changes.activated charcoal pellets wholesale  The penetration point of the components with relatively weak adsorption capacity was significantly advanced, while the penetration time of the components with strong adsorption capacity was delayed. In this paper, E-L equation and IAST theory are used for theoretical prediction and analysis of multi-component adsorption equilibrium, and compared with experimental results.https://www.wyactivatedcarbon.com/  The results show that although the prediction of total adsorption amount by E-L equation is in good agreement with the experimental results, the prediction of each component adsorption amount by E-L equation often produces positive and negative deviation, and the average error is usually more than 20%. However, IAST can eliminate the positive and negative deviation well, and the average error is less than 10%, which is more consistent with the experimental results. The operating parameters showed that the adsorption capacity of activated carbon would decrease with the increase of temperature, gas velocity or humidity. The appropriate operating range is: temperature within 40℃, gas speed between 0.1~0.5 m/s, humidity is best not more than 40%. In this range, the relationship between pressure drop and gas velocity basically conforms to Ergun equation. 
Activated carbon adsorption performance parameters02021-06-09 20:22:27
Microwave heating can produce good effects in the preparation and modification of activated carbon (S2. Microwave modification, many backwater hole is opened, the distributed capacitance change obviously, promoting the improvement of the adsorption. The microwave power and irradiation time are key determinants of modified activated carbon adsorption performance. On the mechanism of microwave carbonization and activation, it is generally believed thatwood based activated carbon manufacturer  Plant waste is mostly made of plant fiber raw materials, in the plant body under the action of capillary, modified solution absorbed by material whole fully, between fiber is filled with the subtle space, make the dry material volume expansion after soaking wet, and reaction. Because of the water in the raw material, modified solution constitute a polar molecule, with a strong absorption of microwave dielectric properties,Therefore, polar molecules collide and rub violently with microwave frequency, generating a large amount of heat, which makes water and modified solution volatilize rapidly, and generate steam pressure, which explodes out from the inside of the raw material to the outside. This sharp action makes the fiber space of the raw material expand and produce sharp drying.In this way, the raw material has a more obvious pore structure and a larger internal specific surface area than before microwave irradiation. Compared with the traditional heating method, the mechanism of microwave in the preparation process of activated carbon is completely different.It shows its unique advantages: high efficiency, energy saving, uniformity, selectivity, low pollution, high thermal efficiency, low energy consumption, simple process and equipment and small footprint, conducive to automation, low carbon loss, and recovery of useful substances.https://www.dxdcarbon.com/  
Ding Xinda activated carbon carbon adsorption and carbon principle and adsorption price02021-11-29 22:43:36
Its adsorption is selective, and non-polar substances are easier to be adsorbed than polar substances.In the same series of substances, the higher the boiling point of the substance, the more tolerantEasy to be adsorbed, the greater the pressure,activated carbon from china  the lower the temperature, the greater the concentration, the greater the amount of adsorption.On the contrary, decompression and heating are beneficial to gas desorption.It is often used for gas adsorption,Separation and purification, recovery of solvents, decolorizing agents for sugar solution, grease, glycerin, medicine, deodorant for drinking water and refrigerators, filter agent for gas masks,It can also be used as a catalyst or metal salt catalyst carrier.Early production of activated carbon raw materials for wood, hard nut shell or animal bones, later mainly used coal, after dryingDistillation, activation treatment after the production of activated carbon methods are :① steam, gas activation method.Carbon is activated by water vapor or carbon dioxide at 850~900℃. gold coconut shell activated carbon activated carbon is a kind of very small granular has a large surface area, and more tiny holes in the granular - capillary. The capillary has very strong adsorption capacity, due to the granular surface area is large, so a good contact with with gas (impurities). When these gases (impurities) encounter capillary by adsorption, purification effect. Activated carbon surface area of the study is very important, only the BET specific surface area detecting data of active carbon method detected result is reliable, domestic at present there are many instruments can only make direct comparison method of detection, 

Ask New Question  

  • You are not logged in,answer will be Anonymous.Set Nickname | Sign In | Sign Up
  • tags separate by ','
  • Shortcuts:Ctrl+Enter

Latest Questions