Chemical properties of activated carbon related questions

Answers
Asked by
Updated
Chemical properties of activated carbon02021-10-19 00:27:32
Powdered activated carbon The general use of medicinal or chemical pure activated carbon. This kind of activated carbon particles is very fine, in powder form, the total surface area is particularly large, the adsorption capacity is very strong, the adsorption capacity is also very large, is the strongest kind of activated carbon adsorption force. But because the particles are too fine, the flow rate is too slow in the process of chromatography, the operation of pressure or decompression is needed, the procedure is more complicated, and the adsorption selectivity of various components is also poor, so it is less used in chromatography.activated charcoal powder  Medicinal or chemical pure activated carbon before leaving the factory after impurity treatment and metal limit inspection, can be used directly for chromatography. Industrial activated carbon is not processed by impurities before leaving the factory, often contains metal ions, affecting the separation effect, so it must be treated before use, its treatment methods are two www.activated-carbon-pellets.com 
Chemical properties of activated carbon02021-12-09 23:12:48
In domestic has been eliminated. Specific surface area test unified the multi-point BET method at home and abroad, specific surface area measurement standards are developed at home and abroad is based on BET test method, please see our national standard (GB/T 19587-2004) - gas adsorption BET principle of solid material specific surface area measurement methods. Specific surface area testing is actually the more time-consuming jobs, as the adsorption capacity of sample is different, some sample testing may need to spend the whole dayTime, if the test process is not fully automated, the tester can not leave at any time, and should be highly focused, observe the dashboard, control the knob, a little careless will lead to the failure of the test process, which will waste a lot of valuable time of the tester. activated carbon gold mining  F - Sorb 2400 specific surface tester is really able to BET method detection instruments (both direct comparison method), the more important F - Sorb 2400 specific surface tester is by far the only specific surface area of the fully automated intelligent testing equipment, the test results with the international high consistency, the stability is very good also, at the same time reduce the human error, improve accuracy test results. activated carbon company 
Chemical properties of activated carbon02021-06-22 01:39:08
Microwave heating can produce good effects in the preparation and modification of activated carbon (S2. Microwave modification, many backwater hole is opened, the distributed capacitance change obviously, promoting the improvement of the adsorption. The microwave power and irradiation time are key determinants of modified activated carbon adsorption performance. On the mechanism of microwave carbonization and activation, it is generally believed thatactivated carbon wholesale price  Plant waste is mostly made of plant fiber raw materials, in the plant body under the action of capillary, modified solution absorbed by material whole fully, between fiber is filled with the subtle space, make the dry material volume expansion after soaking wet, and reaction. Because of the water in the raw material, modified solution constitute a polar molecule, with a strong absorption of microwave dielectric properties,Therefore, polar molecules collide and rub violently with microwave frequency, generating a large amount of heat, which makes water and modified solution volatilize rapidly, and generate steam pressure, which explodes out from the inside of the raw material to the outside. This sharp action makes the fiber space of the raw material expand and produce sharp drying.In this way, the raw material has a more obvious pore structure and a larger internal specific surface area than before microwave irradiation. Compared with the traditional heating method, the mechanism of microwave in the preparation process of activated carbon is completely different.It shows its unique advantages: high efficiency, energy saving, uniformity, selectivity, low pollution, high thermal efficiency, low energy consumption, simple process and equipment and small footprint, conducive to automation, low carbon loss, and recovery of useful substances.https://www.dxdcarbon.com/  Many theoretical problems in this new field, especially the microwave heating mechanism, need to be further studied, and the mathematical model of the heating process needs to be established 
Chemical properties of activated carbon02021-09-23 23:48:21
Activated carbon (AC) is a kind of porous carbon material with developed pore structure and large specific surface area, which is prepared by using biological organic matter (such as wood, coke, petroleum coke, coal and various nut shells, etc.). It is a kind of high quality adsorbent.https://www.granular-activated-carbon.com/  With the development of industry, its application is more and more extensive. At present, it has been widely used in the field of environmental protection, food industry and medicine.coal based activated carbon factory  Industry, agriculture and many other fields. In recent years, one of the research hotspots of activated carbon is to use cheap agricultural and forestry wastes as raw materials and simple and clean process to prepare biomass activated carbon with high economic benefit and good adsorption performance. If the agricultural and forestry wastes are effectively utilized and turned into treasures, it can not only create certain economic benefits, but also reduce its pollution to the environment, and achieve the purpose of treating waste with waste. 
Chemical properties of activated carbon02021-06-22 18:53:29
The purification efficiency of activated carbon adsorption method is 99.2%~99.3%. For the treatment of large air volume and low concentration of organic waste gas, it is agreed that this method is the most mature and reliable technology at home and abroad, but the T art process is too long, the operation cost is high, and it is often more difficult to need a stable steam source. In view of these problems, combined with the characteristics of this graduation design and only body requirements, the use of activated carbon fixed bed adsorption system for industrial organic waste gas purification, the selection of honeycomb activated carbon as adsorbent.The process system is compact and integrated with adsorption and desorption.yrdcarbon  The waste gas produced in the production process, mainly of benzene, toluene, xylene, etc., according to the nature of benzene class, this scheme adopts the active carbon as adsorbent to absorb the waste gas, the adsorption bed configuration 2 sets of above commonly, use rotation, when one adsorption bed adsorption of organic adsorption amount of reach regulation, change to another Ⅰ adsorption bed for adsorption purification operation, at the same time to take off one in front of the adsorption bed with regeneration.Desorption is carried out by heating under the action of additional steam, and most of the hotgas released by the tail gas is used for desorption and regeneration of adsorbent in the adsorption bed to achieve the utilization of waste heat.The waste gas volatilized from production is sent to the adsorption tower by centrifugal fan with activated carbon as adsorbent. The gas in the tower is processed through the activated carbon filter layer from right to left and from bottom to top, and the purified gas is discharged into the atmosphere through the exhaust pipe. www.chinactivecarbon.com 
Chemical properties of activated carbon02021-09-23 23:49:01
Activated carbon is a kind of carbon adsorption material with rich pore structure and high specific In view of the above problems, through in-depth analysis of the carbonization process of activated carbon, the design of FX2N PLC as the core controller, Mitsubishi touch screen as the man-machine interface automatic control system, to achieve the automatic control of the carbonization section, improve the degree of automation of equipment. powdered activated carbon supplier  The quality of activated carbon is directly affected by the control performance of furnace temperature and pressure of carbonization furnace.activated carbon pellets wholesale   The carbonization process of carbonization furnace is a complex chemical reaction process, which has the characteristics of multivariable coupling, nonlinear, time delay and so on. It is difficult to establish accurate mathematical model for furnace outlet temperature and furnace tail pressure, and it is difficult to realize it by means of general control process. Through the comparison and analysis of the fuzzy PID control and the parameter self-adjusting fuzzy PID control simulation, the final determination of the parameter self-adjusting fuzzy PID control algorithm, the blower and induced draft fan speed adjustment, the simulation shows that the control effect is good, has a certain application value. 
Chemical properties of activated carbon02021-09-06 23:21:24
The purification efficiency of activated carbon adsorption method is 99.2%~99.3%. For the treatment of large air volume and low concentration of organic waste gas, it is agreed that this method is the most mature and reliable technology at home and abroad, but the T art process is too long, the operation cost is high, and it is often more difficult to need a stable steam source.activated charcoal pellets  In view of these problems, combined with the characteristics of this graduation design and only body requirements, the use of activated carbon fixed bed adsorption system for industrial organic waste gas purification, the selection of honeycomb activated carbon as adsorbent.The process system is compact and integrated with adsorption and desorption. www.chinactivecarbon.com  
Chemical properties of activated carbon02022-01-03 21:44:16
                                                               The removal capacity of organic matter by catalytic oxidation of honeycomb ceramics was higher than that by ozone oxidation. The maximum removal rate of FP was about 2 times higher than that of ozonation. In the continuous flow test, the removal effect of catalytic oxidation on UV2s4 is obvious at low ozone dosage, and the removal rate of UV2s4 is 16.7% higher than that of ozone at 1 mg/L, which is the result of the high proportion of horizontal push flow in the honeycomb ceramic catalytic reactor and the rapid increase of liquid phase ozone concentration. In addition, the catalytic oxidation of honeycomb ceramics on BrO; When ozone dosage is L mg/L, catalytic oxidation effluent BrO; The content is 38.8% lower than that of ozone oxidation. Activated carbon catalyst can promote the decomposition of ozone. The consumption rate of liquid phase ozone in activated carbon catalytic secondary oxidation process is 71.2% higher than that in ozone secondary oxidation process. The analysis of the relationship between ozone consumption and organic matter content in activated carbon catalytic secondary oxidation process shows that activated carbon can react directly with ozone or act as a free radical initiator in the process of ozone decomposition, especially when the organic matter content in water is low. When ozone dosage is L mg/L, the MIB removal rate of catalytic secondary oxidation is about L times higher than that of ozone secondary oxidation. When the concentration of ozone in water is about 1.5 mg/L, the catalytic secondary oxidation makes BrO; The concentration decreased by 0.04mg/L. 
Chemical properties of activated carbon02021-08-30 00:15:42
The experimental results show that the surface structure of the activated carbon material modified by FeSO changes: the specific surface area decreases, the surface oxygen content increases, the plane of the random layer graphite carbon net is destroyed to a certain extent, and the ammonia absorption capacity and benzene absorption performance of the sample are greatly enhanced.He ChunHong et al. [reported the research progress of supporting activated carbon materials in the removal of SO; the removal ability of SO was significantly enhanced after supporting Co, Ni, Mg, and V compounds, which was due to the formation of Co(OH)2, Ni(OH)2, Mg (OH)2, and V,0 microcrystals on the surface of activated carbon after supporting, which enhanced the desulfurization activity of activated carbon.  https://www.granular-activated-carbon.com  Adsorption capacity refers to the amount of adsorbents adsorbed on the adsorbent per unit mass under certain conditions. It is usually expressed in terms of K adsorbents /kg of adsorbent or mass percentage, which is a sign of the adsorption capacity of the adsorbent. In industry, the amount of adsorption is called the activity of the adsorbent.coal based granular activated carbon  The activity of the adsorbent can be expressed in two ways :(1) the static activity of the adsorbentUnder certain conditions, the equilibrium adsorption capacity of the adsorbent is its static activity.For a certain adsorption system, the static activity depends only on the adsorption temperature and the concentration or partial pressure of the adsorbed substance. Dynamic activity of adsorbents Under certain operating conditions, the gas mixture by adsorption bed, adsorption by adsorption, adsorption after a period of time, when starting from the adsorbent in the laminar flow of the gas adsorbed mass (or its concentration reaches a specified value), think bed fire, adsorption properties of adsorbent adsorption quantity at this time is called dynamic activity of adsorbent. The activity is not only related to the characteristics of adsorbents and adsorbents, but also related to temperature, concentration and operating conditions. 
Chemical properties of activated carbon02021-06-23 19:14:45
Microwave heating can produce good effects in the preparation and modification of activated carbon (S2. Microwave modification, many backwater hole is opened, the distributed capacitance change obviously, promoting the improvement of the adsorption. The microwave power and irradiation time are key determinants of modified activated carbon adsorption performance. On the mechanism of microwave carbonization and activation, it is generally believed thatwww.activated-carbon-pellets.com  Plant waste is mostly made of plant fiber raw materials, in the plant body under the action of capillary, modified solution absorbed by material whole fully, between fiber is filled with the subtle space, make the dry material volume expansion after soaking wet, and reaction. Because of the water in the raw material, modified solution constitute a polar molecule, with a strong absorption of microwave dielectric properties,Therefore, polar molecules collide and rub violently with microwave frequency, generating a large amount of heat, which makes water and modified solution volatilize rapidly, and generate steam pressure, which explodes out from the inside of the raw material to the outside. This sharp action makes the fiber space of the raw material expand and produce sharp drying.In this way, the raw material has a more obvious pore structure and a larger internal specific surface area than before microwave irradiation. Compared with the traditional heating method, the mechanism of microwave in the preparation process of activated carbon is completely different.It shows its unique advantages: high efficiency, energy saving, uniformity, selectivity, low pollution, high thermal efficiency, low energy consumption, simple process and equipment and small footprint, conducive to automation, low carbon loss, and recovery of useful substances.activated carbon manufacturer   Many theoretical problems in this new field, especially the microwave heating mechanism, need to be further studied, and the mathematical model of the heating process needs to be established 
Chemical properties of activated carbon02021-06-23 19:56:45
Microwave heating can produce good effects in the preparation and modification of activated carbon (S2. Microwave modification, many backwater hole is opened, the distributed capacitance change obviously, promoting the improvement of the adsorption. The microwave power and irradiation time are key determinants of modified activated carbon adsorption performance. On the mechanism of microwave carbonization and activation, it is generally believed thatactivated carbon manufacturer   Plant waste is mostly made of plant fiber raw materials, in the plant body under the action of capillary, modified solution absorbed by material whole fully, between fiber is filled with the subtle space, make the dry material volume expansion after soaking wet, and reaction. Because of the water in the raw material, modified solution constitute a polar molecule, with a strong absorption of microwave dielectric properties,Therefore, polar molecules collide and rub violently with microwave frequency, generating a large amount of heat, which makes water and modified solution volatilize rapidly, and generate steam pressure, which explodes out from the inside of the raw material to the outside. This sharp action makes the fiber space of the raw material expand and produce sharp drying.In this way, the raw material has a more obvious pore structure and a larger internal specific surface area than before microwave irradiation. Compared with the traditional heating method, the mechanism of microwave in the preparation process of activated carbon is completely different.It shows its unique advantages: high efficiency, energy saving, uniformity, selectivity, low pollution, high thermal efficiency, low energy consumption, simple process and equipment and small footprint, conducive to automation, low carbon loss, and recovery of useful substances.www.activated-carbon-pellets.com  Many theoretical problems in this new field, especially the microwave heating mechanism, need to be further studied, and the mathematical model of the heating process needs to be established 
Chemical properties of activated carbon02021-09-06 23:18:56
Under certain operating conditions, the gas mixture by adsorption bed, adsorption by adsorption, adsorption after a period of time, when starting from the adsorbent in the laminar flow of the gas adsorbed mass (or its concentration reaches a specified value), think bed fire, adsorption properties of adsorbent adsorption quantity at this time is called dynamic activity of adsorbent. The activity is not only related to the characteristics of adsorbents and adsorbents, but also related to temperature, concentration and operating conditions. The kinetic activity value of adsorbent is the main basis for the design of adsorption system. The adsorption rateThe adsorption process often takes a long time to reach equilibrium, and the contact time is limited in the actual production process.Therefore, the amount of adsorption depends on the adsorption rate, and the adsorption rate is related to the adsorption process, the adsorption process can be divided intoThe adsorption process often takes a long time to reach equilibrium, and the contact time is limited in the actual production process.Therefore, the amount of adsorption depends on the adsorption rate, and the adsorption rate is related to the adsorption process, which can be divided into the following steps (1) External diffusion, the adsorbate from the main air flow through the air film around the particles to the outer surface of the adsorbent; (2) Internal diffusion, the adsorbate from the outer surface through micropores to the surface of the adsorbent microporeshttps://www.granular-activated-carbon.com  (3) adsorption, the adsorbent reached the microporous surface of the adsorbent is adsorbedcoal based granular activated carbon  (4) The desorbed adsorbate diffuses to the main body of the gas phase through internal and external diffusionPhysical adsorption process is generally controlled by internal and external diffusion, chemical adsorption is controlled by both surface dynamics and internal and external diffusion.Because of the complexity of the adsorption process and many influencing factors, it is difficult to derive the rate theoretically, so it is generally determined by experience or model experiment. 

Ask New Question  

  • You are not logged in,answer will be Anonymous.Set Nickname | Sign In | Sign Up
  • tags separate by ','
  • Shortcuts:Ctrl+Enter

Latest Questions