The role of activated carbon in the pharmaceutical industry related questions

Answers
Asked by
Updated
The role of activated carbon in the pharmaceutical industry02021-06-10 18:42:24
The focus of the whole production process is the activation section. At the present stage, some domestic activated carbon production enterprises use air as the activation gas in the activation process. Although it is cheap and easy to get, the air used as the activation gas in the production of activated carbon has a high burning loss rate, low product yield and low finished strength of activated carbon particles. The production of activated carbon by steam as activation gas has the advantages of low burning loss rate, high product yield and high strength of activated carbon particles.wood based activated carbon manufacturer  This project adopts the production process, that is, is the use of water vapor is activated, at the same time set up at the end of the activation furnace waste heat boiler to extract the sensible heat, the boiler and could be used to provide the necessary activation water vapor activation furnace, the design in improving the utilization ratio of resources at the same time, reduce the pollutant emissions, reduces the project's impact on the environment during production process.https://www.dxdcarbon.com/   Activation tail gas is treated and discharged by dust removal and desulfurization system after utilization. ⑴ Zinc chip ratio. Zinc chip ratio refers to the weight ratio of anhydrous zinc chloride to absolute raw wood chips. Zinc chip ratio has a decisive influence on the pore structure and adsorption properties of activated carbon. The pore structure of activated carbon is often adjusted by zinc chip ratio, which is the most important factor for the production of activated carbon by zinc chloride method. ⑵ The influence of raw material types. As a result of different species, wood resin content and hardness and other properties are different, thus the chemical penetration ability of wood chips have differences. Fir chips are usually the best, pine chips the next, and hard and miscellaneous chips the worst. ⑶ The moisture content of raw materials. The moisture content of the sawdust affects the rate of chemical penetration into the sawdust particles, thus affecting the impregnation time. When the moisture content of sawdust is more than 30%, the impregnation time is more than 8h. Generally, the moisture content of sawdust should not exceed 5%. According to the different production technology, the moisture content of sawdust has different specific indexes. (4) the influence of wood particle size. When the particle size of wood chips in the production of powdered activated carbon is 6~40 mesh, the particle size of wood chips has no obvious effect on the product quality. The effect of sawdust particle size on product quality is related to the zinc chip ratio used. When the zinc chips are relatively small (such as 80%), the wear resistance and relative density of activated carbon decrease with the increase of sawdust size. When the size of zinc chip is large (e.g. 200%), the wood chip particle size is 0.25~2.0mm, and the wear resistance and relative density of activated carbon are not significantly affected 
The role of activated carbon in the pharmaceutical industry02022-01-03 22:03:28
(1) According to the relevant national standards, the sludge of Liede Sewage Treatment Plant is mainly composed of volatile organic compounds, with a volatile content of 64.86%, which can be used as the main raw material for the preparation of activated carbon.(2) Without adding additives to the sludge, the concentration of sulfuric acid and zinc chloride is 4 mol·L' and the volume ratio is 2:1. The activated carbon prepared has the maximum iodine adsorption value of 549.6 mg·g 'and the yield of 51.3%, which is the better carbon sample prepared by pure sludge and is recorded as SAC.which was recorded as PAC;By single factor experiment, the optimal conditions of carbon production were obtained as follows: pyrolysis temperature 600℃, activator concentration 4 mol · L', pyrolysis time 1.5h, solid-liquid ratio 1:2.5.Orthogonal experiment showed that the influence of each factor was as follows: pyrolysis temperature >Is the activator concentration >Pyrolysis time >www.powdered-activated-carbon.com  Solid-liquid ratio.(4) the main performance of PAC is basically equivalent to 8818 type activated carbon;The concentrations of heavy metals in activated carbon leaching solution of sludge were all qualified.Compared with domestic and foreign research reports, the quality of PAC is in the middle level.(5) Compared with SAC, the specific surface area of PAC is larger, up to 636.8m2·g'. PAC is mainly mesoporous, but also contains some micropores. The adsorption/desorption isotherm shows that PAC is activated carbon with parallel wall slit pore structure.activated carbon pellets wholesale  SEM analysis showed that the surface pores of commercial activated carbon were microporous and relatively uniform, while the surface of SAC and PAC presented irregular porous structure. XRD analysis showed that the commercial activated carbon was amorphous carbon, SAC and PAC were microcrystalline carbon with hexagonal shape structure 
The role of activated carbon in the pharmaceutical industry02021-06-16 18:51:49
Under these conditions, the COD removal rate reached 78.6%, the BOD /COD value increased from 0.168 to 0.353-0.403, and the biodegradability was greatly improved. If Ho is added in three times and the interval time is 10min, the COD removal rate will increase from 78.6% to 80.3%. Therefore, it can be seen that H0: batch addition will further improve the reaction effect.suppliers of activated carbon  After Fenton oxidation treatment, wastewater and activated carbon adsorption, this topic activated carbon adsorption experiments using single factor method, examines different PH, activated carbon adsorption dosing quantity and the influence of adsorption time of wastewater COD removal rate, the results show that after Fenton oxidation treatment without having to adjust PH value, according to the 20 g/L after adding the activated carbon reaction 3 h at room temperature, COD removal rate was 47.3%,, BOD/COD value of 0.438 to 0.625.dxd carbon  The research in this paper has laid a theoretical foundation and provided an experimental basis for the practical application of Fenton oxidation and activated carbon adsorption in the pretreatment of natural gas purification maintenance wastewater in UASB reactor. Deep desulfurization of transportation fuels is receiving increasing attention in theresearch community worldwide due to increasingly stringent regulations and fuelspecifications in many countries for environmental protection purpose. The traditionalhydrodesulfurization process (HDS) is highly efficient in removing thiols and sulfides, but itis less effective for thiophenes and thiophene derivatives. Ultra-deep desulfurization isbecoming even more formidable challenge for HDS with the decreasing lower sulfur in fuels.Therefore, non-hydrodesulfurization technique of liquid fuels has caused intensive concernsfor ultra-deep desulfurization. Recently, the adsorption desulfurization technique and catalyticoxidation-adsorption desulfurization technique have drawn much attention at home andabroad due to its mild reaction condition,low production cost and little environmentalpollutioz. This thesis focuses on the researches of application of activated carbon fiber inadsorption and oxidation-adsorption removal of thiophenic sulfur compounds from oils. 
The role of activated carbon in the pharmaceutical industry02021-12-30 22:51:34
The removal capacity of organic matter by catalytic oxidation of honeycomb ceramics was higher than that by ozone oxidation. The maximum removal rate of FP was about 2 times higher than that of ozonation. In the continuous flow test, the removal effect of catalytic oxidation on UV2s4 is obvious at low ozone dosage, and the removal rate of UV2s4 is 16.7% higher than that of ozone at 1 mg/L, which is the result of the high proportion of horizontal push flow in the honeycomb ceramic catalytic reactor and the rapid increase of liquid phase ozone concentration. In addition, the catalytic oxidation of honeycomb ceramics on BrO; When ozone dosage is L mg/L, catalytic oxidation effluent BrO; The content is 38.8% lower than that of ozone oxidation.activated carbon gold mining  Activated carbon catalyst can promote the decomposition of ozone. The consumption rate of liquid phase ozone in activated carbon catalytic secondary oxidation process is 71.2% higher than that in ozone secondary oxidation process. The analysis of the relationship between ozone consumption and organic matter content in activated carbon catalytic secondary oxidation process shows that activated carbon can react directly with ozone or act as a free radical initiator in the process of ozone decomposition, especially when the organic matter content in water is low. When ozone dosage is L mg/L, the MIB removal rate of catalytic secondary oxidation is about L times higher than that of ozone secondary oxidation. When the concentration of ozone in water is about 1.5 mg/L, the catalytic secondary oxidation makes BrO; The concentration decreased by 0.04mg/L. activated carbon company 
The role of activated carbon in the pharmaceutical industry92022-03-21 00:11:34
Because of these pores, especially the micropores provide a large surface area. The pore volume of activated carbon micropores is generally only 0.25-0.9mL/g, the number of pores is about 1020 lg, and the surface area of all micropores is about 500-1500m2/g, which is usually measured by the BET method, and it is also said to be as high as 3500-5000 m2/g. Activated carbon almost more than 95% of the surface area is in the micropore, so in addition to some macromolecules can not enter, micropore is an important factor to determine the adsorption performance of activated carbon. The pore volume of mesopores is generally about 0.02-1.0 MLLg, and the surface area can be up to several hundred square meters, generally only about 5% of the total activated carbon silkworm species.activated charcoal wholesale australia  Its function can adsorb steam, and can provide a channel for adsorbent to enter the micropore, and can directly adsorb larger molecules. The pore volume of the macropore is generally about 0.2-0.5mL /g, and the surface area is only about 0.5-2m2 /g. Its role is to make the adsorbate molecules quickly penetrate into the smaller pores inside the activated carbon.https://www.dxdcarbon.com/  : as a catalytic carrier, the catalyst is often a small amount of precipitation in the micropore, mostly precipitation in the macropore and mesopore. The surface area of the activated carbon should include the inner surface area and the outer surface area. In fact, the adsorption properties mainly come to the inner surface area of the white Li large, so it can not be mistaken for: the activated carbon grinding and grinding will significantly improve the surface area to improve the adsorption force. Many adsorbations are recursive physical adsorption, that is, the adsorbed matter is a fluid, which is adsorbed by activated carbon at a certain temperature and pressure. At high temperature and low pressure, the adsorbed matter desorbs out, and the inner surface of activated carbon returns to its original state. This is a widely used physical adsorption, also known as van der Waals adsorption academically. 
The role of activated carbon in the pharmaceutical industry02021-12-29 21:08:17
On the basis of industrial test, the technical indexes, pore structure and adsorption properties of activated carbon for water purification by crushing block were analyzed and studied. The results show that there are two kinds of micropores in the activated carbon, and the contribution of micropores to the specific surface area, pore volume and adsorption performance of activated carbon is much larger than that of medium and large pores. It is a kind of activated carbon with low ash content, high strength, activated carbon gold mining narrow pore distribution, high specific surface area and excellent adsorption performance. After analysis and calculation, the mesopar diameter of activated carbon is 6.71A, BET surface area is 764.83m2 /g, Langmuir specific surface area is 1229.5m3 /g, internal specific surface area is 91.50m3 /g, external specific surface area is 673.33m37g, and micropore volume is 0.133 cm3/g. When P/P=0.30, the maximum specific surface area is 809.776 m'7g, and the maximum pore volume is 0.412 cm'/gc activated carbon company 
The role of activated carbon in the pharmaceutical industry02021-12-29 19:52:03
Laboratory studies have shown that ceramic honeycomb activated carbon catalytic ozone oxidation technology and removal of trace organic matter in water has more obvious advantages, but the catalytic oxidation and active carbon process characteristics to be in-depth study, therefore the pilot was investigated through honeycomb ceramic catalytic ozonation and activated carbon catalytic ozonation and activated carbon filter combination process operation characteristics. activated carbon gold mining  Under experimental conditions, the gas-liquid mass transfer capacity of honeycomb ceramic catalytic reactor is slightly lower than that of ozone reactor, but when the gas-water ratio is greater than 0.15, the gas-liquid mass transfer capacity exceeds that of ozone reactor. The gas holdup (Eg) of ozone reactor and honeycomb ceramic catalytic oxidation reactor is 0.19% and 0.15% respectively when the gas volume is 0.L m3/h, indicating that the size of bubbles in the catalytic oxidation reactor is large, which is not conducive to gas-liquid mass transfer. The Pe values of ozone reactor and honeycomb ceramic catalytic reactor were 3.14 and 5.25, respectively, in the liquid pulse addition test, indicating that the liquid level pushing flow component in catalytic oxidation reactor is higher, which is conducive to gas-liquid mass transfer. The gas-liquid mass transfer efficiency of catalytic oxidation reactor is more affected by increasing gas-water ratio. activated carbon company  
The role of activated carbon in the pharmaceutical industry02021-09-23 23:10:16
Industry, agriculture and many other fields. In recent years, one of the research hotspots of activated carbon is to use cheap agricultural and forestry wastes as raw materials and simple and clean process to prepare biomass activated carbon with high economic benefit and good adsorption performance. If the agricultural and forestry wastes are effectively utilized and turned into treasures, it can not only create certain economic benefits, but also reduce its pollution to the environment, and achieve the purpose of treating waste with waste.https://www.granular-activated-carbon.com/  In this paper, using biomass (corn cob, rice husk and peanut shell) as raw material, the experimental research on the preparation of activated carbon from biomass was carried out on the self-built experimental platform, and the activation temperature, activation time, impregnation ratio and impregnation time and other activation and physicochemical characteristics were systematically studied. Activated carbons with different specific surface area and pore structure were prepared by physical activation and chemical activation, changing carbonization and activation conditions. The pore structure of activated carbon was analyzed by ASAP2020M aperture analyzer.coal based activated carbon factory  The surface structure characteristics of activated carbon and the pyrolysis process of biomass under different conditions were studied. The adsorption performance and yield of activated carbon prepared by two methods were discussed and compared. The results show that activation condition and impregnation condition are the most important factors. The optimum specific surface area of activated carbon prepared by physical activation method is 924.48m'/g, and the yield is 26.18%. The optimum specific surface area of activated carbon prepared by chemical activation method is 1200.04 m2g, and the yield is 34%. Although the specific surface area and yield of the chemical activation method are the largest, it can be seen that the activated carbon prepared by the physical activation method has higher economic benefit and environmental protection value considering the economic benefit and environmental protection value of the preparation process comprehensively. Finally, based on the preparation of activated carbon from biomass, the adsorption equilibrium and kinetics of the prepared activated carbon for methylene blue and the adsorption characteristics of mercury in flue gas were studied. The theoretical basis for its application in printing and dyeing wastewater treatment and mercury removal from flue gas is given. 
The role of activated carbon in the pharmaceutical industry02021-12-10 22:24:15
When the temperature is below 600℃, the specific surface area of carbonized material increases with the increase of temperature.When 600~900℃, the specific surface area reaches a certain value: 250~300 m2/g; when above1000℃, the specific surface area shrinks rapidly. activated carbon for gold recovery  When the carbonization temperature is above 800℃, the reaction performance of carbonized compounds and activation gas gradually becomes weaker, so the carbonization temperature is generally below 1000℃. However, if the residual volatile content and thermal effect are taken into account, the most suitable temperature should be 600~700℃39].activated carbon wholesale  The carbonized substance obtained from the carbonization process is placed in water vapor or a mixture of water vapor and combustion gas and heat treated at 800~1000℃, which is called the activation process. The commonly used activation gases are carbon dioxide, water vapor, oxygen, etc., due to the oxidation reaction of these gases on the surface of the carbonized substance, eroding the carbonized substance, thus producing a rich porous structure.(2) Chemical method. Chemical activation method is a method of preparing activated carbon by adding chemicals to the raw materials used or impregnation into the raw materials or carbonized materials, and then heating it at high temperature in inert gas.The chemicals used in chemical activation are generally dehydrating.The more commonly used activator is: inorganic acid varieties have phosphoric acid, sulfuric acid and boric acid, salt varieties have zinc chloride, calcium carbonate and potassium sulfate, alkali varieties have sodium hydroxide, potassium hydroxide, etc. 
The role of activated carbon in the pharmaceutical industry02021-12-27 22:38:48
Therefore, it is of practical significance to explore and seek an effective pretreatment method. In this paper, Fenton oxidation and activated carbon adsorption were combined to pretreat the wastewater from natural gas purification maintenance, in order to improve the subsequent operation efficiency of UASB. www.powdered-activated-carbon.com  This experiment by orthogonal test to determine the Fenton reagent oxidation first preliminary operating conditions, on this basis, carries on the single factor analysis method, the main factors influencing the Fenton reagent treatment effect for each study, investigation of its influence on wastewater COD removal rate, the results show that Fenton oxidation method the optimum operating conditions for natural gas purification overhaul wastewater treatment: HO2 dosing quantity 0.3 mol/L, n (HO)/n (Fe) = systematically, initial pH = 3, reaction temperature 70 ℃, reaction time, 40 min.activated carbon pellets wholesale   Under these conditions, the COD removal rate reached 78.6%, the BOD /COD value increased from 0.168 to 0.353-0.403, and the biodegradability was greatly improved. If Ho is added in three times and the interval time is 10min, the COD removal rate will increase from 78.6% to 80.3%. Therefore, it can be seen that H0: batch addition will further improve the reaction effect. After Fenton oxidation treatment, wastewater and activated carbon adsorption, this topic activated carbon adsorption experiments using single factor method, examines different PH, activated carbon adsorption dosing quantity and the influence of adsorption time of wastewater COD removal rate, the results show that after Fenton oxidation treatment without having to adjust PH value, according to the 20 g/L after adding the activated carbon reaction 3 h at room temperature, COD removal rate was 47.3%,, BOD/COD value of 0.438 to 0.625. The research in this paper has laid a theoretical foundation and provided an experimental basis for the practical application of Fenton oxidation and activated carbon adsorption in the pretreatment of natural gas purification maintenance wastewater in UASB reactor. 
The role of activated carbon in the pharmaceutical industry02021-08-25 23:30:09
Water purification, can remove the organic matter and heavy metal ions and mildewy odor, bacteria and used in water decolorization, used in drinking water industry, beverage, beer, medicine, sugar and other industries water purification, decolorization process and pure water, direct drinking water production equipment;Sewage treatment: can be used to treat the chemical industry, www.powdered-activated-carbon.com electroplating, metallurgy, printing and dyeing, leather, medicine and other sources of sewage, the removal of organic materials, bacteria and organic dyes in the water.Especially the treatment of toxic and harmful wastewater containing high metal ions;Organic solvent recovery: to benzene, ketone, fat, alcohol and other types of organic solvents can be adsorbed recovery;It can be used in solvent recovery devices such as glue spray paint and film, in benzene purification and recovery devices and in environmental protection projects of waste gas and sewage treatment.Health and anti-expansion: made of gas masks, gas and dust masks, gas jackets can have good adsorption and shielding effect on toxic gases Medical treatment and biological engineering: can be used for the manufacture of artificial kidney, liver adsorbent, used in biological engineering for enzyme fixation; pelletized activated carbon  Daily life: can be used in refrigerator deodorization, fruit and vegetable preservation, household water purifier, cigarette filter, deodorization and disease prevention insoles and other daily necessities production;Other aspects: can be used as catalyst carrier, stationary phase of gas chromatography, solar heat collector and precious metal production 
The role of activated carbon in the pharmaceutical industry02021-12-20 00:22:30
Its adsorption is selective, and non-polar substances are easier to be adsorbed than polar substances.In the same series of substances, the higher the boiling point of the substance, the more tolerantEasy to be adsorbed, the greater the pressure, the lower the temperature, the greater the concentration, the greater the amount of adsorption.On the contrary, decompression and heating are beneficial to gas desorption.It is often used for gas adsorption,Separation and purification, recovery of solvents, decolorizing agents for sugar solution, grease, glycerin, medicine, deodorant for drinking water and refrigerators, filter agent for gas masks,It can also be used as a catalyst or metal salt catalyst carrier.Early production of activated carbon raw materials for wood, hard nut shell or animal bones, later mainly used coal, after dryingDistillation, activation treatment after the production of activated carbon methods are :① steam, gas activation method.Carbon is activated by water vapor or carbon dioxide at 850~900℃.activated carbon gold mining  ② chemical activation method.Activated carbon can be obtained after high temperature treatment by using the gas released by the activator or soaking the raw material with the activator.Activated carbon has a micro product structure, the micro product arrangement is completely irregular, the product body has micropores (radius is less than 20[angstroms]=10-10 meters), through the hole (halfDiameter 20~1000), large hole (radius 1000~100000), so that it has a large inner surface, specific surface area of 500~1700 m 2/ g.This determines that activated carbon has good adsorption, can adsorb the metal ions in waste water and waste gas, harmful gases, organic pollutants, pigments and so on. activated carbon company 

Ask New Question  

  • You are not logged in,answer will be Anonymous.Set Nickname | Sign In | Sign Up
  • tags separate by ','
  • Shortcuts:Ctrl+Enter

Latest Questions