The volatiliability of activated carbon related questions

Answers
Asked by
Updated
The volatiliability of activated carbon02021-09-14 19:24:17
When the adsorption speed and desorption speed of activated carbon in the solution is equal, that is, the number of activated carbon adsorption is equal to the number of desorption, the concentration of the adsorbed material in the solution and the concentration on the surface of activated carbon are no longer intermingled, that is, to achieve the balance, the dynamic balance at this time is called activated carbon adsorption balance. www.powdered-activated-carbon.com  At this time, the concentration of the adsorbed substance in the solution is called equilibrium concentration.In aerobic part, a self-made internal circulating biological fluidized bed reactor was used to treat organic pesticide wastewaterThe effects of internal circulating biological fluidized bed on the removal of organic matter and the deamination of organic pesticide wastewater, the change of wastewater biodegradability and acute biological toxicity were investigated.The results show that the internal circulation biological fluidized bed with granular activated carbon as the carrier has a fast speed of membrane and can be cultured in about days by the rapid sludge drainage methodOut of activated sludge.The internal circulating biological fluidized bed with granular activated carbon as the carrier is not sensitive to temperature change at 1 ℃, and has a certain impact resistance ability.Aeration amount has effect on the treatmentToo large or too small aeration will reduce the reactor treatment efficiency.The optimal hydraulic retention time of the internal circulating biological fluidized bed using granular activated carbon as carrier is, and the treatment effect will be affected if the hydraulic retention time is too long or too short.activated carbon pellets wholesale  At the aeration rate of /,During hydraulic retention, the total helium removal rate is.%,.%, water effluent/up tothe biodegradability of wastewater was significantly improved, and the acute biological toxicity was reduced by %.When the efficiency of internal circulating activated carbon biological fluidized bed treatment is.%, the reaction is obtained 
The volatiliability and total pore area of activated carbon02021-09-14 19:29:55
Activated carbon adsorption, is the use of activated carbon on the solid surface of the water adsorption or a variety of substances, in order to achieve the role of water purification. The adsorption of activated carbon is produced in two aspects.One is that the molecules inside the activated carbon are subjected to equal forces in all directions while the molecules on the surface are subjected to uneven forces.This makes other points adsorbed on its surface, which is physical adsorption;The other is due to the chemical action between activated carbon and adsorbed substances, which is chemical adsorption.The adsorption of activated carbon is the result of the comprehensive action of the above two kinds of adsorption.Activated carbon adsorption, is the use of activated carbon on the solid surface of the water adsorption or a variety of substances, in order to achieve the role of water purification.activated carbon pellets wholesale  The adsorption of activated carbon is produced in two aspects.One is that the molecules inside the activated carbon are subjected to equal forces in all directions while the molecules on the surface are subjected to uneven forces.This makes other points adsorbed on its surface, which is physical adsorption;The other is due to the chemical action between activated carbon and adsorbed substances, which is chemical adsorption.The adsorption of activated carbon is the result of the comprehensive action of the above two kinds of adsorption.powdered activated carbon supplier  When the adsorption speed and desorption speed of activated carbon in the solution is equal, that is, the number of activated carbon adsorption is equal to the number of desorption, the concentration of the adsorbed material in the solution and the concentration on the surface of activated carbon are no longer intermingled, that is, to achieve the balance, the dynamic balance at this time is called activated carbon adsorption balance.  When the adsorption speed and desorption speed of activated carbon in the solution is equal, that is, the number of activated carbon adsorption is equal to the number of desorption, the concentration of the adsorbed material in the solution and the concentration on the surface of activated carbon are no longer intermingled, that is, to achieve the balance, the dynamic balance at this time is called activated carbon adsorption balance. 
The volatiliability and total pore area of activated carbon02021-09-14 19:27:58
Acid-base modification is to use acid, alkali and other substances to treat activated carbon, according to the actual need to adjust the surface functional groups of activated carbon, make it change, improve its ability of adsorption of metal ions, so as to achieve the desired adsorption effect.Acid-base modification of activated carbon is usually carried out to improve the adsorption effect of activated carbon on metal ions represented by copper ions. The commonly used modifiers include HC1, NaOH and citrate 3.It was found that by acid-base modification of common coal activated carbon, the ash content of the activated carbon could be greatly reduced and the specific surface area of the activated carbon could be increased Electrochemical mo https://www.granular-activated-carbon.com/ dification is to change the electrical and chemical properties of activated carbon surface by using micro electric field, so as to improve the adsorption selectivity and performance.It does not need to add chemical agents, does not need to heat, does not cause pollution to the environment, low energy consumption, only a few hundred millivolts, easy to operate.The results show that the adsorption equilibrium of activated carbon is dependent on the electric potential: the adsorption amount of activated carbon increases with the increase of the potential, and the adsorption speed is accelerated;Arpolarity polarization is beneficial to the adsorption of chloroform by activated carbon, while cathodic polarization inhibits the adsorption of chloroform by activated carbon 3-341]. Activated carbon heteroatom carrier and compound modificationActivated carbon has very high stability and good activity, these two basic properties become the activated carbon as a catalyst or catalyst carrier conditions.By introducing certain heteroatoms and compounds on the surface of activated carbon by liquid phase deposition, the adsorption performance of activated carbon can be increased by using the binding effect between these substances and adsorbents.compounds, which has the advantages of increasing the reaction rate and increasing the adsorption capacity.Yang Quanhong et al. 'Using FESO;Activated carbon material was modified. coal based activated carbon factory  
What is the majority of carbonization process of activated carbon? How to produce high quality activated carbon in large quantities02021-07-10 01:00:27
Generally speaking, forming carbon can be mixed with a variety of raw coal to adjust the pore distribution characteristics of the final product, so as to obtain some special application performance, and more than 80% of the pore distribution characteristics of raw coal directly broken carbon has been determined by the raw material, so the performance and use is simple.activated carbon manufacturers  (2) wood activated carbon.It is mshell/core activated carbon.Such as coconut shell carbon, apricot kernel carbon, peach kernel carbon, etc.(4) petroleum activated carbon.Using petroleum asphalt, petroleum coke as raw materials, made of activated carbon products.resin activated carbon.Using phenolic resin, waste ion exchange resin as raw materials, through a special process of activity.Carbon products, sometimes fibrous carbon also falls into this category.High - definition watermark of cut document under air(6) other small varieties of activated carbon products. Made of animal blood blood carbon, made of animal bones bone charcoal (there is very little, but bone charcoal carbon main ingredients of hydroxy calcium phosphate), with active carbon molecular sieve made of various materials, made of strong base and carbon materials of high surface area activated carbon, is made of organic polymer solution after mold made of special process method of activated carbon, activated carbon aerogels and so on. coal activated carbon manufacturer  Some of them are very small production and dosage, and some are still in the laboratory research stage, so they are included in the category of small varieties of activated carbon products. ade of all kinds of hard wood, crop wastes, and other industrial and agricultural wastes containing lignocellulose The beansMaterial as raw material, through the chemical method, physical method or physical-chemical combination of activated carbon. 
Why activated carbon granular shell activated carbon has such a good effect02021-06-28 18:55:05
High-quality granular activated carbon must have good adsorption performance and strength. Like powdery activated carbon, the adsorption performance of granular activated carbon depends largely on the characteristics of pore structure. The adsorption performance index can be analyzed and characterized by different methods, such as the decolorization performance of activated carbon expressed by methylene blue. Other performance indexes include iodine adsorption value, caramel decolorization rate, etc.dxdcarbon carbon  The pore structure characteristics and specific surface area of activated carbon are usually obtained by measuring nitrogen adsorption isotherm at low temperature with adsorption In addition, the adsorption capacity of activated carbon also has a great relationship with its internal pore structure, pore size distribution and surface chemical properties. activated carbon suppliers in uae  Chemical method in addition to certain micropores, macropores, there are more mesopores (transition pores), so it is more suitable for the application of liquid phase, adsorption of larger molecules of substances, such as sugar solution has a good decolorization effect; When purifying water quality, it can also remove the colored material well and achieve the specified chroma requirements. The kinetic activity value of adsorbent is the main basis for the design of adsorption system. The adsorption rateThe adsorption process often takes a long time to reach equilibrium, and the contact time is limited in the actual production process.Therefore, the amount of adsorption depends on the adsorption rate, and the adsorption rate is related to the adsorption process, the adsorption process can be divided intoThe adsorption process often takes a long time to reach equilibrium, and the contact time is limited in the actual production process.Therefore, the amount of adsorption depends on the adsorption rate, and the adsorption rate is related to the adsorption process, which can be divided into the following steps (1) External diffusion, the adsorbate from the main air flow through the air film around the particles to the outer surface of the adsorbent; (2) Internal diffusion, the adsorbate from the outer surface through micropores to the surface of the adsorbent micropores (3) adsorption, the adsorbent reached the microporous surface of the adsorbent is adsorbed (4) The desorbed adsorbate diffuses to the main body of the gas phase through internal and external diffusionPhysical adsorption process is generally controlled by internal and external diffusion, chemical adsorption is controlled by both surface dynamics and internal and external diffusion.Because of the complexity of the adsorption process and many influencing factors, it is difficult to derive the rate theoretically, so it is generally determined by experience or model experiment. 
Activated carbon increases with molecular weight and activated carbon point02021-09-13 01:05:58
The purification efficiency of activated carbon adsorption method is 99.2%~99.3%. For the treatment of large air volume and low concentration of organic waste gas, it is agreed that this method is the most mature and reliable technology at home and abroad, but the T art process is too long, the operation cost is high, and it is often more difficult to need a stable steam source. In view of these problems, combined with the characteristics of this graduation design and only body requirements, the use of activated carbon fixed bed adsorption system for industrial organic waste gas purification, the selection of honeycomb activated carbon as adsorbent.The process system is compact and integrated with adsorption and desorption.www.powdered-activated-carbon.com  The waste gas produced in the production process, mainly of benzene, toluene, xylene, etc., according to the nature of benzene class, this scheme adopts the active carbon as adsorbent to absorb the waste gas, the adsorption bed configuration 2 sets of above commonly, use rotation, when one adsorption bed adsorption of organic adsorption amount of reach regulation, change to another Ⅰ adsorption bed for adsorption purification operation, at the same time to take off one in front of the adsorption bed with regeneration.Desorption is carried out by heating under the action of additional steam, and most of the hotgas released by the tail gas is used for desorption and regeneration of adsorbent in the adsorption bed to achieve the utilization of waste heat.The waste gas volatilized from production is sent to the adsorption tower by centrifugal fan with activated carbon as adsorbent. The gas in the tower is processed through the activated carbon filter layer from right to left and from bottom to top, and the purified gas is discharged into the atmosphere through the exhaust pipe. pelletized activated carbon 
Activated carbon are widely used Activated carbon purifies how clean water is 02021-07-18 23:14:58
Adsorption capacity refers to the amount of adsorbents adsorbed on the adsorbent per unit mass under certain conditions. It is usually expressed in terms of K adsorbents /kg of adsorbent or mass percentage, which is a sign of the adsorption capacity of the adsorbent. In industry, the amount of adsorption is called the activity of the adsorbent.activated carbon powder suppliers  The activity of the adsorbent can be expressed in two ways :(1) the static activity of the adsorbentUnder certain conditions, the equilibrium adsorption capacity of the adsorbent is its static activity.For a certain adsorption system, the static activity depends only on the adsorption temperature and the concentration or partial pressure of the adsorbed substance.https://www.activated-carbon-pellets.com   Dynamic activity of adsorbents Under certain operating conditions, the gas mixture by adsorption bed, adsorption by adsorption, adsorption after a period of time, when starting from the adsorbent in the laminar flow of the gas adsorbed mass (or its concentration reaches a specified value), think bed fire, adsorption properties of adsorbent adsorption quantity at this time is called dynamic activity of adsorbent. The activity is not only related to the characteristics of adsorbents and adsorbents, but also related to temperature, concentration and operating conditions. 
What is the difference between coconut shell activated carbon and columnar activated carbon?02021-02-02 17:57:10
1. First of all, it is clear from the appearance that the columnar activated carbon has the appearance of black cylindrical particles. coconut shell activated carbon for gold recovery The appearance of coconut shell activated carbon is black amorphous granular. 2. The difference between columnar activated carbon and coconut shell activated carbon in terms of material. The columnar activated carbon is made of fine anthracite as raw material and refined by advanced technology. Coconut shell activated carbon is made of fine coconut shell through a series of production processes. 3. Columnar activated carbon and coconut shell activated carbon have different physical and chemical indicators and components. Coconut shell activated carbon and columnar activated carbon can also be used for the purification of toxic gases, waste gas treatment, industrial and domestic water purification, solvent recovery, etc. buy bulk activated carbon pellets Based on the standards produced by activated carbon manufacturers, which one to choose depends on the needs of users and the scope of use. 4. The price of columnar activated carbon and coconut shell activated carbon can be said to be very different. Compared with coconut shell activated carbon with the same effective content or composition, the price of coconut shell activated carbon is much higher than that of columnar activated carbon. 
I love activated carbon. Activated carbon is good for the environment02021-06-29 19:39:21
Activated carbon powder injection combined with bag dust collector (ACI+ BF) is an effective and widely used method to control dioxin emission from incinerator flue gas.https://www.activated-carbon-pellets.com/  In order to provide reference and theoretical basis for the preparation and selection of activated carbon for the adsorption of dioxins, this paper carried out a study on the combined technology of activated carbon injection and double bag dust collector, the characteristics of activated carbon adsorption for dioxins and the influencing factors of activated carbon adsorption for dioxins.The adsorption and desorption isotherms of 13 kinds of commercial activated carbon were determined by low temperature nitrogen adsorption method, and the physical structures of activated carbon were calculated according to BET, T-Plot, BJH and DFT theory, and the iodine value and methylene blue value of 4 kinds of activated carbon were detected. The physical structure characteristics of activated carbon were analyzed in detail to prepare for the subsequent experiment. Using small activated carbon fixed bed adsorption gas phase dioxin test bench, a typical activated carbon adsorption dioxin factors affecting the experimental study, discusses the types of dioxin adsorption activated carbon and activated carbon fixed bed adsorption gas phase characteristics of dioxins, and discusses the adsorption temperature and adsorption time of activated carbon adsorption of dioxins.The results showed that the specific surface area and micropore volume of activated carbon had weak correlation with the adsorption efficiency of dioxins.wan yang carbon   The mesopore volume of activated carbon is an important factor to determine the adsorption capacity of dioxins. The surface area of the pore size between 2 nm and 20nm plays a key role in the adsorption of dioxins.The higher the adsorption temperature, the lower the adsorption efficiency of activated carbon.The longer the adsorption time, the lower the adsorption efficiency of activated carbon.There is no selective adsorption of gaseous dioxins in activated carbon fixed bed. 
Activated carbon surface adsorption and activated carbon strength02021-09-06 18:55:02
Principle of activated carbon adsorptionwww.powdered-activated-carbon.com  activated carbon is a kind of very small granular has a large surface area, and more tiny holes in the granular - capillary. The capillary has very strong adsorption capacity, due to the granular surface area is large, so a good contact with with gas (impurities). When these gases (impurities) encounter capillary by adsorption, purification effect. Activated carbon surface area of the study is very important, only the BET specific surface area detecting data of active carbon method detected result is reliable, domestic at present there are many instruments can only make direct comparison method of detectionIn domestic has been eliminated. Specific surface area test unified the multi-point BET method at home and abroad, specific surface area measurement standards are developed at home and abroad is based on BET test method, please see our national standard (GB/T 19587-2004) - gas adsorption BET principle of solid material specific surface area measurement methods. Specific surface area testing is actually the more time-consuming jobs, as the adsorption capacity of sample is different, some sample testing may need to spend the whole dayTime, if the test process is not fully automated, the tester can not leave at any time, and should be highly focused, observe the dashboard, control the knob, a little careless will lead to the failure of the test process, which will waste a lot of valuable time of the tester.pelletized activated carbon   F - Sorb 2400 specific surface tester is really able to BET method detection instruments (both direct comparison method), the more important F - Sorb 2400 specific surface tester is by far the only specific surface area of the fully automated intelligent testing equipment, the test results with the international high consistency, the stability is very good also, at the same time reduce the human error, improve accuracy test results. The adsorption capacity of activated carbon on each gas (unit: mL /cm3):H2, O2, N2, CI2, CO2 4.5, 35, 11, 494, 97 The main factors affecting the adsorption of activated carbon ① the nature of activated carbon adsorbent The larger the surface area, the stronger the adsorption capacity; Activated carbon is a non-polar molecule, easy to adsorb non-polar or very low polarity adsorbent The size of the activated carbon adsorbent particle, the structure and distribution of the fine pore and the surface chemical properties also have a great influence on the adsorption. 
Activated carbon sales of various specifications of activated carbon02021-08-31 20:16:57
Acid-base modification is to use acid, alkali and other substances to treat activated carbon, according to the actual need to adjust the surface functional groups of activated carbon, make it change, improve its ability of adsorption of metal ions, so as to achieve the desired adsorption effect.Acid-base modification of activated carbon is usually carried out to improve the adsorption effect of activated carbon on metal ions represented by copper ions. The commonly used modifiers include HC1, NaOH and citrate 3.It was found that by acid-base modification of common coal activated carbon, the ash content of the activated carbon could be greatly reduced and the specific surface area of the activated carbon could be increasedwww.powdered-activated-carbon.com  Electrochemical modification is to change the electrical and chemical properties of activated carbon surface by using micro electric field, so as to improve the adsorption selectivity and performance.It does not need to add chemical agents, does not need to heat, does not cause pollution to the environment, low energy consumption, only a few hundred millivolts, easy to operate.The results show that the adsorption equilibrium of activated carbon is dependent on the electric potential: the adsorption amount of activated carbon increases with the increase of the potential, and the adsorption speed is accelerated;Arpolarity polarization is beneficial to the adsorption of chloroform by activated carbon, while cathodic polarization inhibits the adsorption of chloroform by activated carbon 3-341]. Activated carbon heteroatom carrier and compound modificationActivated carbon has very high stability and good activity, these two basic properties become the activated carbon as a catalyst or catalyst carrier conditions.By introducing certain heteroatoms and compounds on the surface of activated carbon by liquid phase deposition, the adsorption performance of activated carbon can be increased by using the binding effect between these substances and adsorbents.compounds, which has the advantages of increasing the reaction rate and increasing the adsorption capacity.Yang Quanhong et al. 'Using FESO;Activated carbon material was modified. pelletized activated carbon 
Principle of activated carbon reaction Activated carbon02021-07-18 20:47:03
Activated carbon, is black powder or block, granular, honeycomb amorphous carbon, but also a regular arrangement of crystalline carbon.In addition to carbon elements, activated carbon also contains two kinds of admixtures: one is the chemical combination of elements, mainly oxygen and hydrogen, these elements are due to incomplete carbonization and residual in the carbon,https://www.activated-carbon-pellets.com   or in the activation process, foreign non-carbon elements and activated carbon surface chemical combination;Another kind of admixture is ash, which is the inorganic part of activated carbon, and ash in active carbon is easy to cause secondary pollution.Because of its strong adsorption, activated carbon is widely used in production,In the life.Activated carbon material is processed by the amorphous carbon, has a large specific surface area, the gas, solution of inorganic or organic matter and colloidal particles have good adsorption capacity.Activated Carbon materials mainly include Activated Carbon (AC) and Activated Carbon Fibers (ACF), etc.Activated carbon material as a kind of excellent adsorbent, mainly because of its unique adsorption surface structure and surface chemical properties.Activated carbon material has stable chemical properties and high mechanical strength. activated carbon powder suppliers 

Ask New Question  

  • You are not logged in,answer will be Anonymous.Set Nickname | Sign In | Sign Up
  • tags separate by ','
  • Shortcuts:Ctrl+Enter

Latest Questions