Activated carbon adsorption performance parameters related questions

Answers
Asked by
Updated
Activated carbon adsorption performance parameters02022-01-12 23:19:42
Factors such as [10. For honeycomb activated carbon, the wall thickness is a very important parameter, by changing the wall thickness to improve its adsorption efficiency. Under the same porosity, thickness increases, the honeycomb carbon content per unit volume also will increase, which can improve the adsorption capacity. This is because the wall thickness increases, the fluid channel in the cellular cross-sectional area reduced, so the real surface or volume flow rate will increase. At the same time, the contact between adsorbate and carbon efficiency will, there is a balance between the two. Under the given conditions, the balance will determine adsorption increase or decrease. If the adsorbate at higherthe diffusion rate diffuses to the inside of the honeycomb wall, and the empty adsorption site can be continuously adsorbed, so the thick-walled honeycomb should have better adsorption efficiency and adsorption capacity"Determination of air velocity and cross-sectional area of empty towerThe empty tower gas velocity is the velocity of gas passing through the entire cross section of the adsorber.The selection of air velocity not only directly determines the size and pressure drop of the adsorber, but also affects the adsorption efficiency.gold adsorption on activated carbon  If the gas speed is very small, the size of the adsorber is large and uneconomical.www.chinactivecarbon.com   If the gas velocity is too large, the pressure drop will increase and the adsorption efficiency will be affected.The optimum gas velocity was determined by experiment. The adsorption design can not pursue too high adsorption efficiency, the empty tower speed value is reduced, it will make the adsorption bed volume, the amount of adsorbent and equipment cost increased greatly;On the contrary, it is not appropriate to take too large empty tower gas speed. Although the equipment cost is low, the adsorption efficiency drops a lot, and the pressure drop of the system will rise rapidly with the increase of the empty tower speed, resulting in excessive power consumption. Therefore, due to the selection of the appropriate air speed of the empty tower, the most suitable air speed of the empty tower is 0.8~1.2m/s"21, according to the empirical conclusion, this design determines Air velocity of empty tower :U= 1.0m /s.Original conditions:Treatment air volume :Q=20000 m'h, design temperature is 35° C, pressure is 1.01325×103Pa Since the proportion of air in exhaust gas is far greater than that of pollutants, the properties of exhaust gas can be approximately viewed as the thermophysical properties of dry air. Please refer to Appendix 9 of Principles of Chemistry to obtain the following data:Properties of air mixture:Fluid density P;=1.147kg/ m', viscosity u,= 1.94×10-5 Pa.S, specific heat capacity C,=1.005kJ/(kg."C) 
Activated carbon adsorption performance parameters02021-06-09 20:22:27
Microwave heating can produce good effects in the preparation and modification of activated carbon (S2. Microwave modification, many backwater hole is opened, the distributed capacitance change obviously, promoting the improvement of the adsorption. The microwave power and irradiation time are key determinants of modified activated carbon adsorption performance. On the mechanism of microwave carbonization and activation, it is generally believed thatwood based activated carbon manufacturer  Plant waste is mostly made of plant fiber raw materials, in the plant body under the action of capillary, modified solution absorbed by material whole fully, between fiber is filled with the subtle space, make the dry material volume expansion after soaking wet, and reaction. Because of the water in the raw material, modified solution constitute a polar molecule, with a strong absorption of microwave dielectric properties,Therefore, polar molecules collide and rub violently with microwave frequency, generating a large amount of heat, which makes water and modified solution volatilize rapidly, and generate steam pressure, which explodes out from the inside of the raw material to the outside. This sharp action makes the fiber space of the raw material expand and produce sharp drying.In this way, the raw material has a more obvious pore structure and a larger internal specific surface area than before microwave irradiation. Compared with the traditional heating method, the mechanism of microwave in the preparation process of activated carbon is completely different.It shows its unique advantages: high efficiency, energy saving, uniformity, selectivity, low pollution, high thermal efficiency, low energy consumption, simple process and equipment and small footprint, conducive to automation, low carbon loss, and recovery of useful substances.https://www.dxdcarbon.com/  
Activated carbon adsorption performance parameters02021-06-11 00:59:21
The experimental results show that the adsorption equilibrium of pure components is in good agreement with the Langmuir equation. In the case of multi-component adsorption, due to the competition and interference between each component, the component with strong adsorption ability can replace the other component that has been absorbed, so that the penetration curve of each component has obvious changes.activated charcoal pellets wholesale  The penetration point of the components with relatively weak adsorption capacity was significantly advanced, while the penetration time of the components with strong adsorption capacity was delayed. In this paper, E-L equation and IAST theory are used for theoretical prediction and analysis of multi-component adsorption equilibrium, and compared with experimental results.https://www.wyactivatedcarbon.com/  The results show that although the prediction of total adsorption amount by E-L equation is in good agreement with the experimental results, the prediction of each component adsorption amount by E-L equation often produces positive and negative deviation, and the average error is usually more than 20%. However, IAST can eliminate the positive and negative deviation well, and the average error is less than 10%, which is more consistent with the experimental results. The operating parameters showed that the adsorption capacity of activated carbon would decrease with the increase of temperature, gas velocity or humidity. The appropriate operating range is: temperature within 40℃, gas speed between 0.1~0.5 m/s, humidity is best not more than 40%. In this range, the relationship between pressure drop and gas velocity basically conforms to Ergun equation. 
Study on Preparation of Modified Activated Carbon and Its Adsorption Performance of Heavy Metals02022-01-12 23:18:50
Factors such as [10. For honeycomb activated carbon, the wall thickness is a very important parameter, by changing the wall thickness to improve its adsorption efficiency. Under the same porosity, thickness increases, the honeycomb carbon content per unit volume also will increase, which can improve the adsorption capacity. This is because the wall thickness increases, the fluid channel in the cellular cross-sectional area reduced, so the real surface or volume flow rate will increase. At the same time, the contact between adsorbate and carbon efficiency will, there is a balance between the two. Under the given conditions, the balance will determine adsorption increase or decrease. If the adsorbate at higherthe diffusion rate diffuses to the inside of the honeycomb wall, and the empty adsorption site can be continuously adsorbed, so the thick-walled honeycomb should have better adsorption efficiency and adsorption capacity"Determination of air velocity and cross-sectional area of empty towerThe empty tower gas velocity is the velocity of gas passing through the entire cross section of the adsorber.The selection of air velocity not only directly determines the size and pressure drop of the adsorber, but also affects the adsorption efficiency. www.powdered-activated-carbon.com  If the gas speed is very small, the size of the adsorber is large and uneconomical. If the gas velocity is too large, the pressure drop will increase and the adsorption efficiency will be affected.The optimum gas velocity was determined by experiment. imagitarium activated carbon pellets  
Ding Xinda activated carbon carbon adsorption and carbon principle and adsorption price02021-11-29 22:43:36
Its adsorption is selective, and non-polar substances are easier to be adsorbed than polar substances.In the same series of substances, the higher the boiling point of the substance, the more tolerantEasy to be adsorbed, the greater the pressure,activated carbon from china  the lower the temperature, the greater the concentration, the greater the amount of adsorption.On the contrary, decompression and heating are beneficial to gas desorption.It is often used for gas adsorption,Separation and purification, recovery of solvents, decolorizing agents for sugar solution, grease, glycerin, medicine, deodorant for drinking water and refrigerators, filter agent for gas masks,It can also be used as a catalyst or metal salt catalyst carrier.Early production of activated carbon raw materials for wood, hard nut shell or animal bones, later mainly used coal, after dryingDistillation, activation treatment after the production of activated carbon methods are :① steam, gas activation method.Carbon is activated by water vapor or carbon dioxide at 850~900℃. gold coconut shell activated carbon activated carbon is a kind of very small granular has a large surface area, and more tiny holes in the granular - capillary. The capillary has very strong adsorption capacity, due to the granular surface area is large, so a good contact with with gas (impurities). When these gases (impurities) encounter capillary by adsorption, purification effect. Activated carbon surface area of the study is very important, only the BET specific surface area detecting data of active carbon method detected result is reliable, domestic at present there are many instruments can only make direct comparison method of detection, 
Ding Xinda activated carbon carbon adsorption and carbon principle and adsorption02021-11-29 22:42:41
With the rapid development of pharmaceutical preparation industry and primary molecular material industry, the microencapsulated activated carbon products coated with polymer materials have been successfully trial-produced in foreign countries, and applied in clinical practice, the medical care and treatment effect is very good, many of them have been put into the market, and have achieved good economic and social benefits. gold recovery activated carbon  It is worth noting that there is a shortage of activated carbon in China. For a long time, the production of drugs using activated carbon as raw materials has been kept in the laboratory, and no products have been marketed or used in clinical trials.coconut activated carbon factory  Experts said that with the continuous improvement of people's life quality and health care consciousness enhancement, as well as the rapid development of all kinds of industrial, environmental pollution has been increasingly serious, people an opportunity to contact with a variety of harmful material, activated carbon and activated carbon as the leading raw material to produce medicines and health products, medical market will become a major conventional leading consumer products, Market demand will be on the rise year by year, is a new economic growth point in the pharmaceutical and chemical market, its economic and social benefits will increase year by year. 
Chemical adsorption and physical adsorption of activated carbon02021-06-09 18:29:13
Activated carbon is a carbon adsorption material with coal, wood and nut shell as raw materials, used in gas adsorption. Separation, purification and separation of liquid purification and other fields. The industrial application of activated carbon by appearance distinguish forming granular activated carbon, are there not finalize the granular activated carbon, powdered activated carbon, activated carbon fiber, etc., main application fields including wastewater treatment, activated carbon depth clean drinking water, medicine and food decolorizing refining, precious metal extraction, gas separation and purification, solvent recovery, and military and civil protection.activated carbon suppliers canada  Taking coal as raw material to the production of coal based activated carbon is a kind of has a developed interspaces structure of carbonaceous adsorption material, has good chemical stability and mechanical strength, coal based activated carbon products can be widely used in decoloring purification, solvent recovery, gas separation, gas purification, and various kinds of water treatment and other fields, some through special processing, the special T also can be used as a high-performance activated carbon desulfurization agent, catalyst and catalyst carrier, mountain in the acid and alkali resistant, heat resistant, granular activated carbon on adsorption saturation after failure, can be a party to regenerate.dxd carbon  The application of coal-based activated carbon is divided into liquid phase and gas phase according to the characteristics of the material. The liquid phase is mainly used in decolorization, recovery of precious metals and water treatment. Gas phase is mainly used in gas purification and recovery, industrial waste gas treatment, flue gas desulfurization and gas protection, etc. In recent years, some foreign activated carbon manufacturers have developed coal-based activated carbon with special adsorption capacity by adopting new processes, new methods and advanced raw material treatment technology, which has greatly improved and enhanced the performance of coal-based activated carbon products, expanded the application field and highlighted a broader market prospect. 
Iodine adsorption value and adsorption capacity of activated carbon0CLMnb2021-08-26 02:59:39
Microwave heating can produce good effects in the preparation and modification of activated carbon (S2. Microwave modification, many backwater hole is opened, the distributed capacitance change obviously, promoting the improvement of the adsorption. The microwave power and irradiation time are key determinants of modified activated carbon adsorption performance. On the mechanism of microwave carbonization and activation, it is generally believed thathttps://www.granular-activated-carbon.com  Plant waste is mostly made of plant fiber raw materials, in the plant body under the action of capillary, modified solution absorbed by material whole fully, between fiber is filled with the subtle space, make the dry material volume expansion after soaking wet, and reaction. Because of the water in the raw material, modified solution constitute a polar molecule, with a strong absorption of microwave dielectric properties,Therefore, polar molecules collide and rub violently with microwave frequency, generating a large amount of heat, which makes water and modified solution volatilize rapidly, and generate steam pressure, which explodes out from the inside of the raw material to the outside. This sharp action makes the fiber space of the raw material expand and produce sharp drying.In this way, the raw material has a more obvious pore structure and a larger internal specific surface area than before microwave irradiation. Compared with the traditional heating method, the mechanism of microwave in the preparation process of activated carbon is completely different.It shows its unique advantages: high efficiency, energy saving, uniformity, selectivity, low pollution, high thermal efficiency, low energy consumption, simple process and equipment and small footprint, conducive to automation, low carbon loss, and recovery of useful substances.coal based granular activated carbon  Many theoretical problems in this new field, especially the microwave heating mechanism, need to be further studied, and the mathematical model of the heating process needs to be established 
Combined Equations (5) and (10) can calculate the total amount of Pb and 21Bi atoms in activated carbon after adsorption for any length of time (i.e., the total number of activated carbon Y).Let n=0 in Equation (10), then the accumulation and attenuation 02022-01-14 22:57:28
Combined Equations (5) and (10) can calculate the total amount of Pb and 21Bi atoms in activated carbon after adsorption for any length of time (i.e., the total number of activated carbon Y).Let n=0 in Equation (10), then the accumulation and attenuation of total atomic amount of 2Pb and 2Bi (total number of activated carbon Y) after the removal of activated carbon can be calculated in Equation (10).In fact, if thin layer activated carbon is used, the value of N should be equal to the product of the adsorption coefficient of activated carbon and radon concentration, while the radon adsorption coefficient of activated carbon mainly depends on the type of activated carbon and is affected by temperature, humidity and other factors. gold adsorption onto activated carbon  When the radon adsorption coefficient of activated carbon is constant,n is proportional to the concentration of radon. In this case, Equation (10) represents the functional relationship among the total number of activated carbon V, radon concentration and adsorption (or exposure) time. Therefore, the concentration of radon in the environment can be calculated according to the total number of activated carbon and adsorption time.Simulation calculation and result analysis of total number of activated carbon According to Equations (5) and (10), a computer program can be written to calculate the relationship between the total number of Y in the process of radon adsorption on activated carbon and the relationship between the total number of Y after the removal of activated carbon and the change of time. activated carbon manufacturers uae  
Ding Xinda activated carbon carbon adsorption and carbon principle02021-11-29 22:41:57
② chemical activation method.Activated carbon can be obtained after high temperature treatment by using the gas released by the activator or soaking the raw material with the activator.Activated carbon has a micro product structure, the micro product arrangement is completely irregular, the product body has micropores (radius is less than 20[angstroms]=10-10 meters), through the hole (halfDiameter 20~1000), large hole (radius 1000~100000), so that it has a large inner surface, specific surface area of 500~1700 m 2/ g.This determines that activated carbon has good adsorption, can adsorb the metal ions in waste water and waste gas, harmful gases, organic pollutants, pigments and so on. gold coconut shell activated carbon  Industry should beActivated carbon also requires high mechanical strength, good wear resistance, its structure is stable, small energy required for adsorption, in order to be conducive to regeneration.Activated carbon for oilDecolorization, deodorization, gas separation, solvent recovery and air conditioning of fat, beverage, food and drinking water, used as catalyst or adsorbent for body and gas mask.Physical characteristics:Activated carbon is a kind of multi-aperture carbonization, has a very rich pore structure, has good adsorption characteristics, its adsorption by physical and chemicalAbsorbed from the force, the appearance of the color and lustre is black.Its composition in addition to the main carbon, but also contains a small amount of hydrogen, nitrogen, oxygen, its structure is shaped like a hexagon, due to the irregular hexagon structure, determine the characteristics of its body also incandescentand high surface area, each gram of activated carbon has the equivalent of 1000 square meters than the surface. 
Activated carbon surface adsorption and activated carbon strength02021-09-06 18:55:02
Principle of activated carbon adsorptionwww.powdered-activated-carbon.com  activated carbon is a kind of very small granular has a large surface area, and more tiny holes in the granular - capillary. The capillary has very strong adsorption capacity, due to the granular surface area is large, so a good contact with with gas (impurities). When these gases (impurities) encounter capillary by adsorption, purification effect. Activated carbon surface area of the study is very important, only the BET specific surface area detecting data of active carbon method detected result is reliable, domestic at present there are many instruments can only make direct comparison method of detectionIn domestic has been eliminated. Specific surface area test unified the multi-point BET method at home and abroad, specific surface area measurement standards are developed at home and abroad is based on BET test method, please see our national standard (GB/T 19587-2004) - gas adsorption BET principle of solid material specific surface area measurement methods. Specific surface area testing is actually the more time-consuming jobs, as the adsorption capacity of sample is different, some sample testing may need to spend the whole dayTime, if the test process is not fully automated, the tester can not leave at any time, and should be highly focused, observe the dashboard, control the knob, a little careless will lead to the failure of the test process, which will waste a lot of valuable time of the tester.pelletized activated carbon   F - Sorb 2400 specific surface tester is really able to BET method detection instruments (both direct comparison method), the more important F - Sorb 2400 specific surface tester is by far the only specific surface area of the fully automated intelligent testing equipment, the test results with the international high consistency, the stability is very good also, at the same time reduce the human error, improve accuracy test results. The adsorption capacity of activated carbon on each gas (unit: mL /cm3):H2, O2, N2, CI2, CO2 4.5, 35, 11, 494, 97 The main factors affecting the adsorption of activated carbon ① the nature of activated carbon adsorbent The larger the surface area, the stronger the adsorption capacity; Activated carbon is a non-polar molecule, easy to adsorb non-polar or very low polarity adsorbent The size of the activated carbon adsorbent particle, the structure and distribution of the fine pore and the surface chemical properties also have a great influence on the adsorption. 
The carbon layer of activated carbon adsorption concept and on the molecular organic matter02021-09-06 20:25:13
Using small activated carbon fixed bed adsorption gas phase dioxin test bench, a typical activated carbon adsorption dioxin factors affecting the experimental study, discusses the types of dioxin adsorption activated carbon and activated carbon fixed bed adsorption gas phase characteristics of dioxins, and discusses the adsorption temperature and adsorption time of activated carbon adsorption of dioxins.The results showed that the specific surface area and micropore volume of activated carbon had weak correlation with the adsorption efficiency of dioxins. https://www.granular-activated-carbon.com  The mesopore volume of activated carbon is an important factor to determine the adsorption capacity of dioxins. The surface area of the pore size between 2 nm and 20nm plays a key role in the adsorption of dioxins.The higher the adsorption temperature, the lower the adsorption efficiency of activated carbon.The longer the adsorption time, the lower the adsorption efficiency of activated carbon.There is no selective adsorption of gaseous dioxins in activated carbon fixed bed. coal based granular activated carbon  

Ask New Question  

  • You are not logged in,answer will be Anonymous.Set Nickname | Sign In | Sign Up
  • tags separate by ','
  • Shortcuts:Ctrl+Enter

Latest Questions